Reinhardt MWS 10 Manual Download Page 33

Page: 33 / 141

REINHARDT

System- und Messelectronic GmbH

Bergstr. 33 86911 Diessen-Obermühlhausen Postfach 12 41 D-86908 Diessen Tel. 08196 - 934100

MWS_55_e.indb Page 33

geändert am 04.12.2020 von DO

Manual MWS 55 / MWS 88 / MWS 10 and Sensors 55

to table of contents

3.10.1.1 Available commands:

ATTRIB

CD / CHDIR

COPY

DEL

DIR

EXIT

FIND

FORMAT

FTIME

HELP

MD / MKDIR

MOUNT

REN

SHELL

TYPE

WRITE

3.10.1.2 Description of the commands

ATTRIB

<+R|-R|+A|-A|+H|-H|+S|-S> <name>

Changes the attributs of a file or directory. The attributs must be typed in capital letters! The

order doesn't matter.

+R -> Set to Read-Only

-R -> Remove Read-Only

+A -> Set to Archiv

-A -> Remove Archiv

+H -> Set to Hide

-H -> Remove Hide

+S -> Set to System

-S -> Remove System

<name> - Change path into directory

CHDIR

<name> - Change path into directory

Changes into the specified sub directory

COPY

<src_name> <dst_name>

Copies the file <src_name> to <dst_name>

Summary of Contents for MWS 10














































































































































Search results

Summary of Contents for MWS 10

Reviews:

Reinhardt MWS 10, Manual, Page: 33 / 141

Search results

Summary of Contents for MWS 10

Reviews: