Reichhardt ULTRA GUIDANCE PSR ISO Page 98 Operator'S Manual Download

Page: 98 / 132

PAGE 98

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER

PSR SONIC

6.6.5. Crop Edge cross wise

Display:

Main screen

Set drive mode according to the adjoined picture (see chapter

4.5.).

Tap the function key

to switch between left and right crop

edge cross wise.

Advice!

In the drive mode crop edge cross wise the

distance shows a slight deviation left or right of the

vehicle from the guide line.

Set sensors:

Set sensors according to adjacent pictures. Pay attention that the

measure rays are directed to hit the inside of the corner.

Picture 171:

Main Screen: crop edge cross wise right

Picture 172:

Sensor direction left edge cross

Picture 173:

Sensor direction right edge cross

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Search results

Summary of Contents for ULTRA GUIDANCE PSR ISO

Reviews:

Related manuals for ULTRA GUIDANCE PSR ISO

Brands by name

Popular brands