manualshive.com logo in svg

Reichhardt ULTRA GUIDANCE PSR ISO, Operator'S Manual

Share
Download
Reichhardt ULTRA GUIDANCE PSR ISO Operator'S Manual Download Page 14

PAGE 14 

OPERATOR’S MANUAL ULTRA GUIDANCE PSR ISO

CHAPTER 

SYSTEM DESCRIPTION

2.2. 

Base Module

2.2.1.  PSR vBasic

PSR vBasic

 

is the basic hardware which will be integrated into 

the vehicle. It is composed of the wiring harness and mounting 

brackets for the iBox.

PSR vBasic

 stays with the vehicle in which it was installed.

2.2.2.  PSR iBasic

PSR iBasic

 is the intelligent component of ULTRA GUIDANCE PSR 

ISO and consists of:

PSR iBox

 – is the core component of ULTRA GUIDANCE PSR ISO. 

With a PSR-controller, the weather proof distribution box steers all 

functions of ULTRA GUIDANCE PSR ISO. The PSR iBox is installed 

for easy access outside of the tractor cab. Suitable mounting 

brackets are contained in the PSR vBasic. The iBox is lockable 

and provides dirt and weather protected connections for trouble 

free function even when changing vehicles.

ULTRA GUIDANCE PSR ISO can be operated by any ISOBUS terminal.

Picture 1:

PSR iBox

Summary of Contents for ULTRA GUIDANCE PSR ISO





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands