Regency PTO30-NG1 Owners & Installation Manual Download Page 24 | Manualshive

Page: 24 / 44

background image

24

|

Regency Plateau® PTO30-1 Outdoor Gas Fireplace

|

24

installation

919-141a

11/25/13

2

PTO30

NOTE

: If using framing unit with original version of PTO30 (not -1), cut

base in areas shown below and fold down to allow room for the
larger size.

1.

Attach six (6) short vertical supports (Part C) to base (Part D) with

two (2) screws for each support - twelve (12) screws total. Do not
install corner screws.

2.

Rest subassembly and inner tall vertical supports (Part B) on lower

frame (Part A).

3.

Attach inside tall vertical supports (Part B) to short vertical supports

(Part C) with one (1) screw each.

4.

Secure all vertical supports (Part B) with two (2) screws each to

lower frame (Part A).

5

. Place top frame (Part A) on inside tall vertical supports (Part B).

6.

Secure in place with two (2) screws for each support

7.

Manoeuvre in outside tall vertical supports (Part B).

Part B

Part C

Part A

Part B

Part C

Part D

Diagram 1

Cut

Cut

Fold

Fold

Diagram 2 - Base Subassembly

Diagram 3

Diagram 4

Part A

Diagram 5 - Top Frame

Part B

Diagram 6 - Outside Part B

«
...
22
23
24
25
26
...
»

Summary of Contents for PTO30-NG1













































Reviews:

No comments

Related manuals for PTO30-NG1

Brand: IHP Pages: 8

Brand: Wayne Pages: 46

Brand: Wayne Pages: 52

Brand: Valor Pages: 41

Brand: Valor Fires Pages: 12

Brand: Empire Comfort Systems Pages: 4

Brand: HASE Pages: 48

Brand: Quadra-Fire Pages: 36

Brand: Napoleon Pages: 20

Brand: Paramount Fitness Pages: 56

Brand: Paramount Fitness Pages: 14

Brand: United States Stove Pages: 4

Ascent Linear BL56

Brand: Napoleon Pages: 132

Brand: BECAFIRE Pages: 67

Prescott White Mantel

Brand: Early Settler Pages: 4

Brand: Adobelite Pages: 23

Brand: Draftbooster Pages: 13

Brand: Pur Line Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands