background image

 

Regency Plateau® PTO30-1 Outdoor Gas Fireplace

e  |     

11

11

installation

INNER FRAMING DIMENSIONS (REQUIRED)

NOTE:FRAMING MATERIAL NOT SUPPLIED

37-15/16" (964mm)

TOP VIEW

SIDE VIEW

END VIEW

8-3/4" (222mm)

8-3/4" (222mm)

10

-7

/8

" (

27

6m

m

)

37-15/16" (964mm)

NOTE:

   Framing materials must be non-combustible 

when used within 4" of the unit. 

 

       Combustible framing materials may be used 

outside the 4" clearance range.

 

    Finishing materials 

MUST

 be non-combustible.

Consideration should be given to weather / elements 
when choosing framing materials (ie. treated lumber, 
steel stud).

66-15/16" (1700mm)

END VIEW

8-

3/

4"

 (2

22

m

m

)

8-3/4" (222mm)

SIDE VIEW

66-15/16" (1700mm)

10

-7

/8

" (

27

6m

m

)

TOP VIEW

PTO30

PTO60

NOTE:

 PTO30 - Two (2) ventilation grills are required for all enclosures.

 

    This is to alleviate moisture and allow for air to circulate. Minimum recommended size 20" sq (508 mm²) 

ea

.

NOTE:

 PTO60 - Four (4) ventilation grills are required for all enclosures.

 

    This is to alleviate moisture and allow for air to circulate. Minimum recommended size 20" sq (508 mm²) 

ea

.

Vent Location

Vent Location

Vent Location

Vent Location

Vent Location

Vent Location

Summary of Contents for PTO30-NG1













































Reviews: