manualshive.com logo in svg

Regency P36D-LP10, Owners & Installation Manual, Page: 1 / 64

Share
Download
Regency P36D-LP10 Owners & Installation Manual Download Page 1

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.  6988 Venture St., Delta, BC  Canada, V4G 1H4

919-444a

07.14.15

P36D  Zero  Clearance

Direct  Vent  Gas  Fireplace

Owners & Installation Manual

Tested by:

Installer

: Please complete the details on the back cover 

and leave this manual with the homeowner.

Homeowner:

 Please keep these instructions for future reference.

MODELS:    P36D-NG10 Natural Gas     P36D-LP10  Propane

www.regency-fire.com

 

-  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other 

appliance. 

- WHAT TO DO IF YOU SMELL GAS

 • 

Do not try to light any appliance.

  •  Do not touch any electrical switch: do not use any phone in your building.

    Leave the building immediately.

  •  Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's 

 

instructions.

  • If you cannot reach you gas supplier, call the fire department.

   

  Installation and service must be performed by a qualified installer, service agency or the gas supplier.

     WARNING

FIRE OR EXPLOSION HAZARD

F

ailure to follow safety warnings exactly could result in serious

injury, death, or property damage.

 

Summary of Contents for P36D-LP10

































































Reviews:

No comments