Regency HEAT WAVE 946-556 Manual Download Page 1

918-023q

06.17.20

Manufactured by:

FPI Fireplace Products International Ltd.  

6988 Venture St., 

Delta, B.C. Canada, V4G 1H4

Tested by: Intertek

FOR YOUR SAFETY

What to do if you smell gas:

*  Do not try to light any appliance

*  Do not touch any electrical switch: do not 

use any phone in your building.

*  Immediately call your gas supplier from a 

neighbour's phone. Follow the gas supplier's 

instructions.

*  If you  cannot reach your gas supplier, call 

the fire department.

WARNING:  

Improper installation, adjustment, alteration, service or 

maintenance can cause injury or property damage. Refer 

to this manual.   For assistance or additional information 

consult an authorized installer, service agency or the gas 

supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapours 

and liquids in the vicinity of this or any other appliance.

Installation and service must be performed by an author-

ized installer, service agency or the gas supplier.

HEAT WAVE DUCT KIT

KIT # 946-556 & 946-753

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Approved for use with the following

 

Gas Fireplace

 

Models

:

 

www.regency-fire.com

 City 40 Series, City 60 Series, City 72 Series, HZ33CE, HZ54E, HZ40E, P33, P33CE, P33E, 

P36, P36E, P36D, P90, U900E, U1500E, G800EC and G800C 

C#4001172

Summary of Contents for HEAT WAVE 946-556









Reviews: