background image

Please follow these instructions carefully to ensure that
your gate extension is properly installed. Improper
installation could result in the gate becoming dislodged
from the doorway, or unstable. Always make sure the
extension is securely attached to the gate before using. The
safety of your child is your responsibility.

It  is  preferable  to in stall  the  extension on the  hinge  side  of
the  gate.  If  you have  an  application that  requires additional
extensions, please contact the retailer which you
purchased your gate from. We offer,  the following sizes of
extensions for your gate: 4 inch,  6 inch,  12 inch and  24
inch.  They  are  available at  most  retailers that  carry  our
Regalo Products line of metal gates.

Note: If using this gate at the top of  stairs,the 4 Wall Cups
MUST be used . I f not use,the gate could be dislodged from
the opening.

Please read these instructions carefully.

Assembly and Installation Instructions

Contact Regalo for questions and replacement
parts. If in doubt concerning the use of your gate, 
call our customer care line at 952-435-1080.

Regalo International LLC., 14305 Southcross Drive.
Suite 100,  Burnsville, MN 55306.
Made in China.

1. Gate Frame

2. Hardware Pack which should contain:

4 - Threaded Spindle Rods

4 - Adjustable Wheel Spindles

(already assembled to the Spindle Threaded Rods)

Check  that you hav e these contents:

(1)

Important: Keep these

instructions for future

reference

Intended for young children aged six  months  through  24 months.

Check the gate regularly to see if all the hard ware and mountings

are tightened.

To prevent serious injury or death,securely install  gate  or

enclosure and  use according to manufacturer’s instructions.

Never use with a child able  to climb over  or  dislodge the gate or

enclosure.

Never leave child unattended.

Use only with the locking/latching mechanism securely engaged.

Note:If  using  this gate at  the top of stairs,the 4 wall  Cups MUST

beused. If not used,the gate could  be  dislodged from the opening.

WARNING:

Gate Instructions

4 - Wall Cups

4 - Screws

Summary of Contents for 1152










Reviews: