manualshive.com logo in svg

Redline Communications RedMAX AN100U, Administration And Maintenance Manual

Share
Download
Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 132

B-6

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

WARNING: UL aggregated 
Guaranteed Rate exceeds 
Capacity

The aggregate guaranteed minimum 
rates configured for service flows 
using nRTPS, RTPS and UGS 
scheduling exceeds the uplink 
capacity of the sector.

Minimum rates can no longer be guaranteed.

You need to improve your links such that the use 
of a less robust coding rate is possible, or 
remove some guaranteed services. 

If you wish to over subscribe, you should use a 
non-guaranteed scheduling type such as Best 
Effort.

WRONG CRC over I2C

The stored interface configuration 
data has failed an integrity check.

All interface (other than service provisioning) 
configuration will be reset to their default values. 
This is only a problem if it happens more than 
once, concurrently.

Wrong DCD Count in DBPC: 
[SS Id]

A subscriber unit [SS Id] sent a 
Downlink Burst Profile Change 
(DBPC) request with an incorrect DCD 
counter.

Information only. There is no action required.

If this event occurs continuously for the same 
subscriber, then a subscriber reset (from the 
sector controller’s SS Info page) is 
recommended. See “Rebooting the Subscriber 
Unit” on page 3-2.

Initial Ranging Messages

Broadcast Downlink DSA 
Failure: [SS Id] (rsp)

DSA (Dynamic Service Addition) for 
the default downlink/uplink service 
flow failed because the subscriber unit 
(SS ID) sent an unsuccessful 
response code (rsp).

These messages may be logged during initial 
ranging, registration and service flow creation

Default Uplink DSA Failure: 
[SS Id] (rsp)

DSA (Dynamic Service Addition) failed 
because the subscriber unit (SS ID) 
sent an unsuccessful response code 
(rsp).

The sector controller will try to create the service 
flow after 10 seconds. The maximum retry limit is 
3. 

If this event occurs more than 3 times and the 
service flow remains rejected, reboot the 
subscriber unit. See “Rebooting the Subscriber 
Unit” on page 3-2.

Also make sure that adaptive modulation is 
enabled (Admin Tools > Advanced 
Configuration page). if you are not using 
Adaptive Modulation, then reduce the downlink 
modulation. 

DSA Failure: [SS Id], SFID [x] 
(retries)

DSA (Dynamic Service Addition) failed 
because of message retransmissions.

Information only. There is no action required.

DSA Failure: [SS Id], [SFID [x] 
(rsp)

DSA (Dynamic Service Addition) failed 
because the subscriber unit (SS ID) 
sends n unsuccessful response code 
(rsp).

Information only. There is no action required.

Table B-1

AN100U/UX Event Log Messages  (continued)

Message

Description

Comment

Summary of Contents for RedMAX AN100U



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands