Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 130 | Manualshive

Page: 130 / 178

background image

B-4

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

Developer Messages

Access Address: [value in
hex]

This message is displayed only after a
watchdog reset occurs. It provides
information about the software
exception which caused the watchdog
to reset.

This message is not intended for the end
user/operator. If you see this message please
contact [email protected].

Cause Register: [value in hex] This message is displayed only after a

watchdog reset occurs. It provides
information about the software
exception which caused the watchdog
to reset.

This message is not intended for the end
user/operator. If you see this message please
contact [email protected].

Error address: [value in hex],
Error ID: [value in hex]

This message is displayed only after a
watchdog reset occurs. It provides
information about the software
exception which caused the watchdog
to reset.

This message is not intended for the end
user/operator. If you see this message please
contact [email protected].

Exception Program Counter:
[value in hex]

This message is displayed only after a
watchdog reset occurs. It provides
information about the software
exception which caused the watchdog
to reset.

This message is not intended for the end
user/operator. If you see this message please
contact [email protected].

P2-Task: [task name]

This message is displayed only after a
watchdog reset occurs. It provides
information about the software
exception which caused the
watchdog.

This message is not intended for the end
user/operator. If you see this message please
contact [email protected].

IDU-Related Messages

Error when reading from i2c
memory

Hardware failure. There was an error
while reading configuration data.

No action will be taken by the AN100U/UX
software to correct this error. The unit should be
returned. Please contact
[email protected].

Error when writing to i2c
memory

Hardware failure. There was an error
while writing some configuration data.

No action will be taken by the AN100U/UX
software to correct this error. The unit should be
returned. Please contact
[email protected].

Event log cleared by user

Self explanatory

Information only. There is no action required.

Table B-1

AN100U/UX Event Log Messages (continued)

Message

Description

Comment

«
...
128
129
130
131
132
...
»

Summary of Contents for RedMAX AN100U



















































































































































































Reviews:

No comments

Related manuals for RedMAX AN100U

Brand: Gates Pages: 26

Brand: Daga Pages: 28

BAKER HUGHES DPS 5000 Series

Brand: GE Pages: 36

Brand: Oemtools Pages: 8

Brand: U.S. General Pages: 5

Brand: Panasonic Pages: 289

Brand: Datalogic Pages: 248

Brand: Labelmate Pages: 2

Brand: Cateye Pages: 2

UE-12Li100BL IN Series

Brand: UPOWER Ecoline Pages: 2

Brand: SICK Pages: 184

Brand: hepco & becker Pages: 5

Brand: Honda Pages: 6

Brand: PROAIM Pages: 4

Brand: LANSING LIGHTING Pages: 4

Brand: T3 Ping Pong Pages: 2

Brand: FANATEC Pages: 29

efector300 SBU3

Brand: IFM Electronic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands