manualshive.com logo in svg

red lion IAMS0002, Manual, Page: 4 / 40

Share
Download
red lion IAMS0002 Manual Download Page 4

4 LP1109

WARNING

The IAMS devices are designed for connection to hazardous 

electric voltages. 

Ignoring this warning can result in severe personal injury or 

mechanical damage. 

To avoid the risk of electric shock and fire, the safety instructions 

of this manual must be observed and the guidelines fol lowed. 

The specifications must not be exceeded, and the device must 

only be applied as described in the following. 

Prior to the commissioning of the device, this manual must be 

examined carefully. 

Only qualified personnel (technicians) should install these 

devices. If the equipment is used in a manner not specified by 

the manufacturer, the protection provided by the equipment may 

be impaired.

GENERAL

WARNING

Until the devices are fixed, do not connect hazardous voltages to 

the devices. 

The following operations should only be carried out on a discon-

nected devices and under ESD safe conditions: 

  General mounting, connection and disconnection of wires. 

  Troubleshooting the device.

Repair of the device must be done by Red Lion Controls only.

HAZARD OUS 

VOLTAGE

WARNING

To keep the safety distances, the relay contacts on the devices 

must not be connected to both hazardous and non-hazard ous 

volt ages at the same time. 

The IAMS devices must be mounted on a DIN rail according to DIN 

46277.

INSTAL-

LATION

WARNING

Do not open the front plate of the devices as this will cause 

damage to the connector for the display / programming module 

PGMMOD00. This devices contains no DIP-switches or jumpers.

Summary of Contents for IAMS0002









































Reviews:

No comments