Red Jacket LPG Premier Installation Manual Download Page 6

Introduction

Safety Precautions

2

Safety Precautions

The following safety symbols are used throughout this manual to alert you to important safety hazards and 
precautions.

• The equipotential bonding must be carried out by the installer in accordance with the nationally applicable 

installation regulations. For this purpose the piping components of the installed pump must be used.

• Protection against lightning reduces the risk of loss, damage or injury from direct strikes and against low energy 

surges.

• Protection provided by the various methods and approaches as prescribed by NFPA 780 and the IEC 62305 

series of standards. Protection to the electronic equipment, communication and signal lines is ensured by 
providing surge protection to them.

• FIRE HAZARD! Do NOT use power tools during the installation or maintenance of equipment. Sparking could 

ignite fuel or vapors, resulting in fire. Use only spark-proof tools.

Note: This information is generated as a consequence of carrying out the ignition hazard assessment.

EXPLOSIVE

Fuels and their vapors are extremely explo-
sive if ignited.

FLAMMABLE

Fuels and their vapors are extremely flamma-
ble.

WARNING

Warning Alert - read message and follow 
instructions to avoid serious injury, death, or 
substantial property damage.

TURN POWER OFF

Live power to a device creates a potential 
shock hazard. Turn Off power to the device and 
associated accessories when servicing the 
unit.

ELECTRICITY

High voltage exists in, and is supplied to, the 
device. A potential shock hazard exists.

FENCE OFF WORK AREA

Fuels and their vapors are extremely explosive 
if ignited. Keep hazardous zone free of unau-
thorised personnel and vehicles. Put up fenc-
ing and/or barricades to safeguard work area.

WEAR EYE PROTECTION

Wear eye protection when working with pres-
surized fuel lines or epoxy sealant to avoid pos-
sible eye injury.

GLOVES

Wear gloves to protect hands from irritation or 
injury.

READ ALL RELATED MANUALS

Knowledge of all related procedures before 
you begin work is important. Read and under-
stand all manuals thoroughly. If you do not 
understand a procedure, ask someone who 
does.

WARNING

Portions of this product are to be installed and operated in the highly 
combustible environment of a LPG storage tank. It is essential that 
you carefully read and follow the warnings and instructions in this 
manual, failure to do so, can result in damage to property, 
environment, personal injury or death.

OFF

OFF

Summary of Contents for LPG Premier









































Reviews: