REA JET HR pro 2K User Manual Download Page 43

Page: 43 / 189

Instruction manual

Page 43 / 189

REA JET HR

pro

2K / 4K

V 3.5x_001 28.05.2015

Figure 18: View of the operator side of the

REA JET HR

pro

control device

There are three different assembly options available for the

REA JET HR

pro

2K/4K control devices

(installation in cabinet, installation in 19" chassis and direct installation). As the assembly of the
various REA JET HR

pro

control devices do not differ to a great extent, the three variants will be

demonstrated on one REA JET HR

pro

4K control device.

3.2.1.1

Installation in the cabinet of the REA JET HR

pro

2K/4K control device

To install in the cabinet on a DIN supporting rail 35mm (TS35), use REA JET HR

pro

top hat rail

clips on the REA JET HR

pro

4K control device.

Figure 19: Delivery scope REA JET HR

pro

top hat rail clip

3.2.1.2

Installation on a 35 mm supporting rail



) Mount the control device in the retaining elements with the groove on the top side into the

supporting rail and pull downward slightly against the spring tension.



II)

Press the lower edge of the control device forward against the lower side of the

supporting rail

and relieve the spring of the clip.



III

) The lower groove of the top hat rail clip now clasps into the supporting rail.



The top hat rail clips are intended for installation on
a DIN 35 mm supporting rail:
-- REA JET HR

pro

-- REA JET HR

pro

Summary of Contents for JET HR pro 2K






























































































































































































Search results

Summary of Contents for JET HR pro 2K

Reviews:

Related manuals for JET HR pro 2K

Brands by name

Popular brands

REA JET HR pro 2K, User Manual

Search results

Summary of Contents for JET HR pro 2K

Reviews:

Related manuals for JET HR pro 2K

Brands by name

Popular brands