background image

Programmable Antenna Rotator

VH226E User's Manual

Important Information

Important Safety Instructions

1.  Read these instructions.

2.  Keep these instructions.

3.  Heed all warnings.

4.  Follow all instructions.

5.  Do not use this apparatus near water.

6.  Clean only with dry cloth.

7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s 

instructions.

8.  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus 

(including amplifiers) that produce heat.

9.  Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug 

has two blades with one wider than the other. A grounding type plug has two blades and a 

third grounding prong. The wide blade or the third prong are provided for your safety. If 

the provided plug does not fit into your outlet, consult an electrician for replacement of the 

obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience 

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with 

the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to 

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus 

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been 

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or 

moisture, does not operate normally, or has been dropped.

Care and Maintenance

•   Always use a soft cloth to clean the speaker and transmitter. Never use any product containing alcohol 

or other solvents as they may damage the surface.

•   Use caution when plugging the power transformers in an AC outlet to avoid the risk of electric shock.

•   If the speaker are used outside on a deck or patio, make sure you take them indoors in the event of a 

rainstorm to prevent possible damage.

•   Do not operate or store the system in extreme temperatures.
CAUTION:

 Please keep the unit in a good ventilation environment. Do not install the equipment 

in a confined space, such as a book case or similar unit.

For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall 

be easily accessible.
Do not use this apparatus near water.
The apparatus shall not be exposed to dripping or splashing or placed near objects filled with 

liquids.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold 

with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus 

combination to avoid injury from tip-over.
WARNING: 

Please refer the information on exterior bottom enclosure for electrical and safety 

information before installing or operating the apparatus.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
1) This device may not cause harmful interference, and 2) This device must accept any interference 

received, including interference that may cause undesired operation. 
Note: This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, 

uses, and can radiate radio frequency energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communication. However, there is no 

guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or more of 

the following measures: 
•  

Reorient or relocate the receiving antenna.

•  

Increase the separation between the equipment and receiver.

•  

Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.

•  

Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by VOXX Accessories Corporation 

could void the user’s authority to operate the equipment.
Industry Canada Regulatory Information 

 

Avis d’Industrie Canada

CAN ICES-3 (B)/NMB-3 (B) 

 

 

CAN ICES-3 (B)/NMB-3 (B)

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of 
purchase. Attach it here and record the serial and model numbers in case you 
need them. These numbers are located on the product. 
Model No.: ______________________________________________________________
Purchase Date: __________________________________________________________  
Dealer/Address/Phone: ___________________________________________________

IMPORTANT SAFETY INSTRUCTIONS 

PLEASE READ AND SAVE FOR FUTURE REFERENCE

This is class II equipment designed with double or reinforced insulation so it does 

not require a safety connection to electrical earth (US: ground).

Plugging in for power

  AC OUTLET POWER SUPPLY: 120 V ~ 60 Hz

The AC power plug is polarized (one blade is wider than the other) and only fits 

into AC power outlets one way. If the plug will not go into the outlet completely, 

turn the plug over and try to insert it the other way. If it still does not fit, contact 

a qualified electrician to change the outlet, or use a different one. Do not attempt 

to bypass this safety feature.

Installing the Outdoor Drive 

Unit

Step 1: Attach cable to the drive unit

1.  Run cable (not included) to the drive unit.
  IMPORTANT: Up to 150’ (46m) of 22AWG 3 

conductor cable may be used. For longer runs, use heavier 

gauge wire. 

2.  Unscrew the single screw on the bottom door. Swing 

the door open. 

3.  Insert the cable through the grommet on the side of 

the drive unit.  

4.  Separate the cable leads for 1.5”(4cm) and strip off the 

insulation for 0.5”.

Unpacking

Make sure the following pieces are in the box:
(1) Drive unit
(1) Control unit
(1) Remote control
Hardware kit:
  (2)   U Bolts 

(5)   Rotor-Mounting Bolts 

(3)   Short Brackets 

(1)   Long Bracket (with guy-wire holes) 

(10) Nuts 

(8)   Washers

Note:

 Bolts require a 10mm or adjustable wrench (not 

included).

continues on next page...

The MAINS plug is used as the disconnect device, the disconnect device shall 

remain readily operable.

WARNING:

 

TO PREVENT FIRE 

OR ELECTRICAL 

SHOCK HAZARD, DO 

NOT EXPOSE THIS 

PRODUCT TO RAIN 

OR MOISTURE.

Summary of Contents for VH226E



















Reviews: