Operating instructions
RC EYE OneLINK
No. 89036RC
Version 11/13
1. INTRODUCTION
Dear customer,
Thank you for making the excellent decision to purchase this RC Logger® product. You now have
a high-quality product with a name that represents outstanding products.
This product complies with the applicable National standards and regulations. We kindly request
the user to follow the operating instructions, to preserve this condition and to ensure safe
operation! These operating instructions relate to this product. They contain important notices on
commissioning and handling. Please take this into consideration when you pass the product on
to third parties. Please keep these instructions for further reference!
All company names and product designations contained herein are trademarks of the respective
owners. All rights reserved.
We wish you a great deal of enjoyment with your new RC Logger® product!
Please download the latest version of the operating instructions from our
website at www.rclogger.com. Navigate to the product page and open the
“Downloads” tab. Click on “Operating instructions” to start the download.
2. INTENDED USE
This product is intended for working with the RC EYE ONE S (not included) or RC EYE ONE
Xtreme (not included) to allow controlling via branded remote control transmitters. With suitable
cables, the “OneLINK” is compatible with remote control transmitters from the most popular
brands in the model craft industry.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
From here onwards the “RC EYE OneLINK” is referred to as “OneLINK”.
3. DELIVERY CONTENT
>
RC EYE OneLINK
>
2.4 GHz Antenna
>
Futaba box trainer cable (89056RC)
>
JR mono plug trainer cable (89058RC)
>
Micro USB to USB Cable (89060RC)
>
2 x 1.5 V AAA battery
>
Operating instructions
4. PRODUCT COMPATIBILITY
The TX module can be used in combination with the following other RC Logger products:
>
Micro USB Trigger Port Cable (89059RC)
>
Futaba Round Trainer Cable (89057RC)
5. SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
Persons / Product
>
The device is not a toy. Keep it out of the reach of children and pets.
>
Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
>
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
>
Do not place the product under any mechanical stress.
>
If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
>
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
>
Also observe the safety and operating instructions of any other devices which are connected
to the product.
>
Not following the instructions in these operating instructions may result in dangers such as
short circuit, fire, electric shock, etc. Observe the safety information under all circumstances!
Miscellaneous
>
Consult an expert when in doubt about operation, safety or connection of the device.
>
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
>
If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
6. OPERATING ELEMENTS
1
3
4
2
5
6
7
9
8
1 Button “ON/OFF”
2 Button “Bind” / “Select-Frequency”
3 Button “Learning” / “Upgrade-Firmware”
4 Battery compartment
5 Receiver body
6 microUSB port
7 Status LED
8 Antenna connector
9 Antenna
7. INSTALLING THE ANTENNA
Connect the antenna to the “OneLINK” before applying voltage to the
“OneLINK”. If the “OneLINK” is powered on without the antenna installed for
more than 5 mins, it may be damaged.
Connect the included 2.4 GHz antenna to the antenna connector (8) at the top of the
“RC EYE OneLINK”.
8. INSERTING BATTERIES
Open the battery compartment at the rear by sliding the compartment cover towards the bottom.
Insert two AAA type batteries into the compartment. Observe the polarities as indicated in the
battery compartment. After inserting the batteries the status LED (7) lights up.
9. CONNECTING TO A REMOTE TRANSMITTER
When using the “OneLINK”, turn off signal transmission via antenna on your
transmitter. Signal should only be transmitted via trainer port. Read the
operating instructions of your transmitter for more information.
Connect the microUSB port (6) on the “OneLINK” to the trainer port of your transmitter by a
suitable cable. Refer to the cable compatibility table of section “22. Compatibility table” and select
the correct cable for your transmitter. If no transmitter is learned the “OneLINK” waits for correct
learning after first startup.
LED indications
Solid
No signal received from transmitter
Flashing slowly
“OneLINK” is transmitting on the chosen channel
Troubleshooting
Transmitter
Is the transmitter turned on?
Cable
Faulty cable connection. Disconnect and re-connect
the cable.
