manualshive.com logo in svg

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Share
Download
Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 61

 

NautoPilot® 5000 Series 

102-890.NG001-NG003  

Operator Manual 

 

 

 
Edition: 003

 

45 

10000001052 

 

 

1.4.6 

Operation mode Waypoint Steering 

 

Important Note: 

Please refer to chapter 4.5.2 before using waypoint steering 

mode! Waypoint steering is possible with NP 5100 or NP5300 

only! 

 

In waypoint steering mode the route - consisting of 2 or more waypoints -  is 

planned on a GPS, chart plotter or equivalent navigation system. NP5000 receives 

only the data from the navigation system in order to steer the vessel on a certain 

track. The operator must have a good knowledge of the navigation system in use as 

this system controls the autopilot with regards to heading alterations, track changes 

and the corresponding alert philosophy. 

The operator should closely monitor the progress when sailing on a route. In case of 

deviations from the route or any uncertainty the operator should switch to Auto and 

use the heading control function. 

 

Starting Waypoint Steering mode in combination with GPS, chart plotter or 
equivalent navigation system 
 

When the connected navigational system starts transmitting a valid APB- telegram 

(ac- cording to IEC 61162- 1) the waypoint steering mode can be activated by 

activating the Track button on the NP5000 operator unit. Make sure that the 

relevant parameters, such as rudder limit, radius or RoT are adjusted according to 

the planned route. 

 

 

1.4.7 

Manual 

 

 

 

Standalone application:  The mode Manual is not for Autopilot in a Standalone 

 

 

application. It will never be displayed in a Standalone 

 

 
 

 

AS application: 

application. 

 

 

The steering switch is in position HAND. 

 

 

 

Summary of Contents for NautoPilot 5000 Series
































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands