Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 135 | Manualshive

Page: 135 / 191

background image

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

119

10000001052

Table 30

Procedure for a course change in Course Control mode

Course Control mode is active.
The mode is displayed at the top right corner of the dis-
play (Course Ctrl.).

Preselected COG

125.8

Turning the rotary knob will change the set Course Over
Ground value.

Please note: After approx. 15 seconds of inactivity from
rotary knob, the previous Course Over Ground value is
displayed again.

This value is displayed in italic and bold.

The SET LED (near the button) will flash (request to
press the SET button).

Set Course Over Ground

125.8

Pressing the SET button transmits the preselected value
to the controller as the new set Course Over Ground.

The value is now displayed in non- italics.

The SET LED (near the button) is off.

Caution!

Course Approaching is displayed at the top bar of the display.
Rotary knob is disabled and a new set course over ground input is not
possible while the heading change maneuver is running.
If set course over ground value is reached the caution Course Approaching is
no longer displayed. Now it is possible to make a new course change
maneuver.

or

Course Control mode is active.
The mode is displayed at the top right corner of the dis-
play (Course Ctrl.).

«
...
133
134
135
136
137
...
»

Summary of Contents for NautoPilot 5000 Series
































































































































































































Reviews:

No comments

Related manuals for NautoPilot 5000 Series

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: Gainsborough Pages: 2

Brand: Eagle Pages: 3

Brand: Rapid Technic Pages: 152

Brand: R.M. Young Pages: 10

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

Brand: IDEAL Networks Pages: 10

Brand: H&S Pages: 54

Brand: Samson Pages: 2

Brand: Bartscher Pages: 61

Brand: Barreto Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands