Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 126

Page: 126 / 191

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

110

Edition: 003

Preselected heading

Acknowledging the value with the SET button or only with the rotary knob has the

same result, but the procedure is different. This procedure can be used, if a

heading change is in preparation.

Direct heading

Change the heading directly if a heading change is based on a bearing.

4.3.6.1

Preselected heading change in Heading Control mode

Table 24

Procedure for changing preselected heading in Heading Control mode

Heading Control mode is active.
The mode is displayed at the top right corner of the display
(Heading Ctrl.).

Preselected Heading

125.8

Turning the rotary knob will change the preselected heading
value.

Please note: After approx. 15 seconds of inactivity from the
rotary knob, the primary set heading value will be displayed
again.

This value is displayed in italic and colors are inverted.

The SET LED (near the button) will flash (request to press
the SET button).

Set Heading

125.8

Pressing the SET button will transmit the preselected value
to the controller as the new set heading.

The value is now displayed in non- italics and normal colors.

The SET LED (near the button) will be off.

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands