Raytec VARIO2 IP 16 Series Full Installation And Setup Manual Download | Manualshive

Page: 37 / 64

background image

37

Settings / Groups

This page is used to configure the operation of the illuminator based on Photocell

and / or External Inputs, configure the illuminator to operate in Local, VMS or HTTP

mode, assign the illuminator to a Group and configure the deterrent mode of the

illuminator.

The illuminator can be configured to operate from the above inputs independently
and the power level, duration and soft start function can be configured.

«
...
35
36
37
38
39
...
»

Summary of Contents for VARIO2 IP 16 Series

































































Reviews:

No comments

Related manuals for VARIO2 IP 16 Series

Brand: Keiser Pages: 2

Brand: ECA Pages: 3

Brand: Nautilus Pages: 12

Brand: Radarcan Pages: 40

Brand: Olsen Pages: 56

Brand: Waterous Pages: 5

Brand: 3TECH Pages: 32

Brand: 4EVAC Pages: 15

Brand: 4iiii Pages: 36

Brand: 4iiii Pages: 34

Brand: 4EVAC Pages: 27

LOUDEN 200 Series

Brand: ACCO Brands Pages: 144

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: Eaton Pages: 16

Brand: Eaton Pages: 6

Brand: Ecco Pages: 17

Brand: Fellowes Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands