manualshive.com logo in svg

RaySafe i3, Installation & Service Manual, Page: 38 / 39

Share
Download
RaySafe i3 Installation & Service Manual Download Page 38

38

RaySafe i3 Installation & service manual – Technical Data 

TECHNICAL DATA 

REAL-TIME DOSIMETER

CHARACTERISTIC 

MEASURE 

Weight 

34 g (1.2 oz)

Dimensions (W × H × D)

40 × 58 × 17 mm (1.6 × 2.3 × 0.7 in)

Mounting 

Clip and lanyard holder 

Communication interface

USB, radio

Battery type

CR2450, Li/MnO

2

Battery life

Approximately 1 year of normal use

Radio frequency

868.3 MHz, 927.9 MHz or 918.3 MHz (depending on purchased configuration)

REAL-TIME HUB

CHARACTERISTIC 

MEASURE 

Weight 

180 g (6.3 oz)

Dimensions (W × H × D)

184 × 134 × 35 mm (11.8 × 9.8 × 2.4 in)

Power supply 

Power over Ethernet: GT-963003648-T3-PP (included)

Communication interfaces 

Ethernet 100 Mbps, radio

Radio frequency

868.3 MHz, 927.9 MHz or 918.3 MHz (depending on purchased configuration)

VIDEO UNIT

CHARACTERISTIC 

MEASURE 

Weight 

282 g (9.9 oz)

Dimensions (W × H × D)

108 × 83 × 24 mm (4.3 × 3.3 × 0.9 in)

Power supply 

External supply: EA1024PR

Video output 

DVI Digital output: 2x HDMI 1.4a up to 1920×1200 @60Hz (only one can be used 
at a time)

REAL-TIME DOSIMETER RACK 

CHARACTERISTIC 

MEASURE 

Dimensions (WxHxD)

300x63x20 mm (11.8x2.5x0.8 in)

Summary of Contents for i3








































Reviews:

No comments