Raypak TempTracker mod+ Hybrid Installation And Operation Instructions Manual Download Page 27

Page: 27 / 56

TempTracker mod+ Hybrid Installation and Operation Manual

HTC# 059105-00D

Bacnet Mstp startup Menu

-------- SETTINGS ----

Season

Winter

System Target 140

BACK

▲

▼

SELECT

-- ARE YOU SURE? --

Yes

BACK

▲

▼

SAVE

--- BACNET MODE ---

Disable

Enable

BACK

▲

▼

SAVE

- BACNET BAUDRATE -

9600

19200

38400

BACK

▲

▼

SAVE

----MS/TP ADDRESS----

[ ]

BACK

▲

▼

SAVE

---- BACNET ID ----

477000

[

]

BACK

▲

▼

SAVE

When using the TempTracker mod+ Hybrid in a BACnet MS/TP network, the use of BACnet Interface Module is required (#651735).

In addition, each of the Boiler Type and Sensor Type Startup menu option will offer a different list of BACnet variables. See "Boiler

Type" on page 20. See "Sensor Type" on page 20. Also, see "Hybrid - Outdoor Reset - BACnet Variable list" on page 44

Bacnet Mode

Enable, Disable

Default: Disable

Button:

MENU/<System Startup>/.... Sensor Fault/BACnet Mode

• This menu option enables or disables the BACnet MSTP capability. When enabled,

additional BACnet settings shall be available for further customizing.

• Note that if this option was enabled while no BACnet communication is present, the BAcnet

error message will supersede other messages. See "Display Messages" on page 40.

--- BACNET MODE ---

Disable

Enable

BACK

▲

▼

SAVE

Bacnet Baud rate

9600, 19200, 38400

Default: 19200

Button:

MENU/<System Startup>/.... Sensor Fault/BACnet Mode/BACnet Baudrate

• For the control to communicate over a BAcnet MS/TP network, it must use the same Baud

rate as the rest of the network. The control offers three Baud Rates.

• If communication was not successful, the baud rate could be the cause. Check with the

network administrator for the network baud rate. Then match it on the control.

- BACNET BAUDRATE -

9600

19200

38400

BACK

▲

▼

SAVE

Ms/tp address

1 to 127

Default: 64

Button:

MENU/<System Startup>/.... /BACnet Mode/BACnet Baudrate/ MSTP Address

• Each device on the MS/TP network must have a unique address.

• This is the MS/TP address on a RS485 network. Its MS/TP range is 1 though 127.

• The MS/TP address must be provided by the Network Administrator.

----MS/TP ADDRESS----

[ ]

BACK

▲

▼

SAVE

Bacnet Id

1 to 4,000,000

Default: 477,000

Button:

MENU/<System Startup>/.... / MSTP Address / BACnet ID

• The BACnet ID is a unique 32 bit number that identifies the control within the BACnet

network. No two ID shall be the same even if dealing across networks.

• It must be provided by the BACnet Network Administrator.

---- BACNET ID ----

477000

[

]

BACK

▲

▼

SAVE

Summary of Contents for TempTracker mod+ Hybrid

























































Search results

Summary of Contents for TempTracker mod+ Hybrid

Reviews:

Brands by name

Popular brands

Raypak TempTracker mod+ Hybrid, Installation And Operation Instructions Manual

Search results

Summary of Contents for TempTracker mod+ Hybrid

Reviews:

Brands by name

Popular brands