Raymarine LIGHTHOUSE 3 Page 379 Advanced Operation Instructions Download | Manualshive

Page: 379 / 450

background image

• Airports

• Airfields

• Country borders

• Sensitive institutions

The Remote controller and the MFD will alert you that there is a no-fly zone. Your UAV will not enter
the restricted airspace covered by a no-fly zone. You will also be unable to launch your UAV in
restricted airspace. Please refer to the DJI app or the DJI website for more information on no-fly
zones and their locations.

20.5 Getting started

Initial steps to get up and running with your UAV.
1. Using a

USB A to USB Micro B

cable, connect the Micro B end of the cable to the Accessory

connection on the rear of your MFD.

2. Power on the MFD.
3. Obtain a GNSS (GPS) position fix on the MFD.
4. Open the UAV app.
5. Connect the MFD to the internet. (An internet connection is only required the first time you open

the UAV app, after a Factory reset, or after an MFD software update).

Ensure that an internet connection is available on your MFD at the point of registration. If your
vessel is likely to be out-of-range of cellular or satellite internet service at registration time, you
will need to register the UAV before heading out on the water.

6. Wait for successful registration.
7. Power on the UAV’s remote controller.
8. Power on the UAV.
9. Wait for the UAV to obtain a GNSS (GPS) position fix and for the “Ready to go” message to be

displayed on the remote controller’s screen.

10. Connect the USB A end of the USB cable to the relevant connection on the UAV’s remote

controller.

20.6 UAV app page

The UAV app is not displayed on the Homescreen by default. To open the UAV app you must first
create a UAV app page icon on your MFD’s Homescreen.

UAV control features are integrated with the Chart app; when creating a UAV app page it is
recommended that you create a splitscreen Chart / UAV app page.

Follow the instructions detailed in the

5.4 Creating / Customizing an app page

section for information

on creating an app page. Chart / UAV splitscreen app pages will be set to a 30/70 page split by
default.

UAV (Unmanned Aerial Vehicle) app

379

«
...
377
378
379
380
381
...
»

Summary of Contents for LIGHTHOUSE 3



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LIGHTHOUSE 3

Brand: QBC Diagnostics Pages: 65

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: Gardol Pages: 260

Brand: York Fitness Pages: 20

Brand: Qiagen Pages: 48

Brand: Qiagen Pages: 162

Brand: Qazqa Pages: 4

Brand: Qlightec Pages: 12

Brand: Labnet Pages: 12

Brand: Vatech Pages: 137

Brand: Vatech Pages: 68

Brand: Varytec Pages: 52

Brand: Gaspardo Pages: 88

Brand: Posture Pump Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands