Raymarine LIGHTHOUSE 3 Advanced Operation Instructions Download Page 366

Page: 366 / 450

Menu item

Description

Options

Crossover (Low pass filter):

Allows you to select the crossover
frequency. The Low Pass Filter
(LPF) will block all audio frequencies

above

the threshold you specify.

Selecting APF (All Pass Filter) will
allow all frequencies.

• 60 Hz

• 80 Hz

• 120 Hz

• APF

Crossover (High pass filter):

Allows you to select the crossover
frequency. The High Pass Filter
(HPF) will block all audio frequencies

below

the threshold you specify.

Selecting APF (All Pass Filter) will
allow all frequencies.

• 60 Hz

• 80 Hz

• 120 Hz

• APF

Multi-zone volume control:

Allows you to select independent
audio zones that are controlled by
multi-zone volume control.

Note:

Only available on Fusion audio
devices with multi-zone control.

• Audio zones 1–12

Reset:

Performs a factory reset and power
cycle of the SR200.

Note:

Only available on Sirius SR200
devices.

• Reset

Diagnostics mode:

Displays the SR200’s diagnostic
information.

Note:

Only available on Sirius SR200
devices.

• Display diagnostics

Page settings tab

Settings

Description

Data Overlays

Enables configuration of Data overlays

Edit split ratio

Enables you to customize the position of the partitions in
splitscreen app pages.

Adjusting balance and fade controls

From the

Audio settings

menu:

Menu > Audio settings

1. Select the

Balance

setting field or the

Fade

setting field.

The Adjustment slider control is displayed.

366

Summary of Contents for LIGHTHOUSE 3



































































































































































































































































































































































































































































Search results

Summary of Contents for LIGHTHOUSE 3

Reviews:

Brands by name

Popular brands

Raymarine LIGHTHOUSE 3, Advanced Operation Instructions

Search results

Summary of Contents for LIGHTHOUSE 3

Reviews:

Brands by name

Popular brands