Raymarine LIGHTHOUSE 3 Advanced Operation Instructions Download | Manualshive

Page: 313 / 450

background image

1.

Overheat warning

2.

Low oil pressure warning

3.

Water in fuel warning

4.

Low voltage warning

5.

Check engine warning

6.

Steering system warning

7.

Catalyst warning

Tanks

The engine page displays the number of tanks aboard
your vessel, their type, instance number and fill level.

Note:

• The number of tanks and their type is determined

during the installation wizard.

• Tanks require calibration, for more information refer

to

Calibrating tanks

• No more than 6 tanks can be displayed on the engine

page.

• If there are more than 6 tanks detected on your

vessel’s network the engine page will display them
using the following hierarchy: fuel, fresh water, waste
water, gasoline, followed by prioritizing the lowest
instance numbers first.

Engine trim

The trim bar displays the trim level of your engine(s), a
higher blue bar equates to a higher trim percent. The trim
bar will begin to flash if you attempt to set the engine trim
beyond 100%.

313

«
...
311
312
313
314
315
...
»

Summary of Contents for LIGHTHOUSE 3



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LIGHTHOUSE 3

Brand: GALLERY Pages: 18

Brand: Palazzetti Pages: 112

Brand: Makita Pages: 8

Brand: VECTECH Pages: 5

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: Mandam Pages: 9

Brand: DB Industries Pages: 60

Brand: vc999 Pages: 55

Brand: Salsbury Industries Pages: 4

Brand: Fayat Group Pages: 50

Brand: Halyard Pages: 88

Brand: IDEAL Networks Pages: 10

Brand: Velp Scientifica Pages: 12

Brand: Yamaha Pages: 24

Brand: J&M Pages: 33

Brand: Rath Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands