6.8 Dealer calibration — i50 Depth
Dealer Calibration enables you to set:
• User calibration menu access On (default) and Off.
• Display Response for depth readings — Dictates
the rate at which the instrument display responds
to changes in depth data.
• Boat show mode On and Off (default) (Boat
show mode is only available on displays set as
repeaters).
• Reset to factory defaults.
Accessing the Dealer Calibration Menu
During normal operation:
1. Press and hold the
Depth
and
Alarm
buttons
at the same time for approximately 14 seconds,
until the
Dealer Calibration
page is displayed.
+
D12470-2
1
0
15
20
25
30
35
40
45
50
55
60 5
14
D
e pth
A
la rm
Note:
To exit the Dealer Calibration pages at any
time, press and hold the
Depth
and
Alarm
buttons
at the same time for approximately 2 seconds.
Setting access to the User Calibration Menu
From the Dealer Calibration page:
1. Press the
Offset
and
Reset
buttons at the same
time to display the
User Calibration Access
page.
D12471-2
+
O
ffs e t
R
e s e t
2. Use the
Offset
and
Reset
buttons to switch
access to the
User Calibration Menu
On (default) and Off.
Selecting Off disables access to the
User
Calibration Menu
.
Note:
To exit the Dealer Calibration pages at any
time, press and hold the
Depth
and
Alarm
buttons
at the same time for approximately 2 seconds.
Setting the response delay for depth
readings
From the
User Calibration Menu Access
page:
1. Press the
Depth
button until the
Depth
Response
page is displayed (1 press from the
User Calibration Menu Access
page).
D12472-2
D
e pth
2. Use the
Offset
and
Reset
buttons to adjust the
depth response to the required level.
The default level is 12. The levels available are 1
to 15 with level 1 being the slowest update rate
and level 15 the quickest.
Note:
To exit the Dealer Calibration pages at any
time, press and hold the
Depth
and
Alarm
buttons
at the same time for approximately 2 seconds.
Enabling and disabling Boat Show Mode
From the User
Calibration Menu Access
page:
1. Press the
Depth
button until the
Boat Show
Mode
page is displayed (2 presses from
User
Calibration Menu Access
page).
D12473-2
D
e pth
2. Use the
Offset
and
Reset
buttons to switch boat
show mode On and Off (default).
Selecting On will put the display into boat show
mode.
Note:
Boat show mode is only suitable for
demonstration purposes and should NOT be used
whilst your vessel is in use.
Note:
To exit the Dealer Calibration pages at any
time, press and hold the
Depth
and
Alarm
buttons
at the same time for approximately 2 seconds.
Resetting the display to factory defaults
From the User
Calibration Menu Access
page:
1. Press the
Depth
button until the
Factory
Defaults
page is displayed (3 presses from
User
Calibration Menu Access
page).
D12474-2
D
e pth
2. To reset the display to factory default settings:
i.
Use the
Offset
or
Reset
buttons to change
the reset option to Yes.
ii. Press the
Depth
button to reset your display
to factory default settings.
3. After a reset it is recommended that you check
the data master status of the display to ensure
it is set correctly. Refer to
for
details.
Note:
To exit the Dealer Calibration pages at any
time, press and hold the
Depth
and
Alarm
buttons
at the same time for approximately 2 seconds.
38
i50
Summary of Contents for i50 Depth
