manualshive.com logo in svg

Raymar 3460, User Manual, Page: 54 / 171

Share
Download
Raymar 3460 User Manual Download Page 54

3460 Fast’R

3-9

Non-Option Set Parameters

This section describes parameters that are independent of the option set 
selected. Determine whether the default options are correct for your site, 
and set parameters as needed.

Table 3-5. Site-Specific Parameters

Parameter

Default Option

Available Option

Test Options

Accept RDL

AT&T4=On

AT&T5=Off

Modulation Options

Guard Tone

Country-specific

AT&G0=Off

AT&G1=550

AT&G2=1800

EC/DC Options

Buffers

AT

*

NB0=Regular

AT

*

NB1=Reduced

Automatic Call Unit (ACU) Options

Call Progress

ATX0=Modem uses only NO 

CARRIER and CONNECT 

result codes.

ATX1=Modem uses only NO 

CARRIER, CONNECT, and 

CONNECT <Rate> result 

codes.

ATX2=Modem waits for dial 
tone and uses only NO 
CARRIER, CONNECT, 
CONNECT <Rate> and NO 
DIALTONE result codes.

ATX3=Modem detects busy 
signal and uses only NO 
CARRIER, CONNECT, 
CONNECT <Rate>, and 
BUSY result codes.

Summary of Contents for 3460












































































































































































Reviews:

No comments