Raymar 3460 User Manual Download Page 152

Page: 152 / 171

3460 Fast’R

C-16

Light Bars

Some stand-alone modems have front-panel light-bars that display
information about the modem’s current performance:

On modems without light bars, display information with Fast’RVu.

Light Bar Displays

This:

Indicates...

Configured Line Rate & Link Utilization Light Bar (upper row):

The rightmost lit or flashing LED The configured modem receive* rate

The rightmost steadily-lit LED

Actual link utilization

A slowly-flashing LED

An under-utilized link

Configured Data Rate & Throughput (lower row):

The rightmost lit or flashing LED

The maximum available throughput
between modem and computer*

The rightmost steadily-lit LED

Actual throughput

A slowly-flashing LED

Actual throughput is lower than the
maximum available

*Default. To display transmit rate, use the AT

SD1 command.

Light bars flash briefly when a connection is made.

Summary of Contents for 3460












































































































































































Search results

Summary of Contents for 3460

Reviews:

Raymar 3460, User Manual, Page: 152 / 171

Search results

Summary of Contents for 3460

Reviews: