Raymar 3460 User Manual Download Page 150

Page: 150 / 171

3460 Fast’R

C-14

Figure C-3. Card Modem Front Panels

Status LEDs

Cards and stand-alone modems have the following front panel
indicators. On a dual-modem card, each modem has a set of indicators.

Status LED Displa y s

LED

Description

Modem Ready/

Test Mode

•

: modem is ready to interwork with computer

•

Flashing

: Modem is in V.54 test mode

Transmit/Receive
(Data Terminal
Ready)

: computer is asserting DTR (Circuit 108) to modem

Two-Wire Leased- Line and

Four-Wire Leased-Line/

Modem A Off-Line

Configuration Button

Modem A Status LEDs

Modem Status LEDs

Modem B Off-Line

Configuration Button

MODEM A

OLC

MODEM B

3460

Modem B Status LEDs

3460

Dial-Line Dual-Modem Card

Single-Modem Card

Off-Line

Configuration Button

OLC

With Dial-Line Alternative

Summary of Contents for 3460












































































































































































Search results

Summary of Contents for 3460

Reviews:

Raymar 3460, User Manual, Page: 150 / 171

Search results

Summary of Contents for 3460

Reviews: