RAYLASE AXIALSCAN Manual Download | Manualshive

Page: 5 / 71

background image

Basic safety instructions

Chapter 1

MN025 / v2.1.0

3-Axis Subsystems for Laser Beam Deflection

5

1

BASIC SAFETY INSTRUCTIONS

1.1

Laser safety

The user is responsible for safe operation and for safeguarding the surrounding area against
hazards that can be caused by laser radiation. OEM customers must ensure compliance with
all local and national regulations.

1.2

Laser shutter

The subsystem - consisting of a linear translator module and a deflection unit - is designed to
focus and deflect an input laser beam and output it again. The subsystem cannot block or
weaken the laser beam. To prevent unwanted emission of the laser beam, above a particular
danger class the laser device must be fitted with a shutter (



page 7, Classification of laser

The laser device must be of sufficient quality that the laser beam can only be emitted at the
beam output on the deflection unit.

«
...
3
4
5
6
7
...
»

Summary of Contents for AXIALSCAN








































































Reviews:

No comments

Related manuals for AXIALSCAN

Brand: Kawai Pages: 19

Brand: Calculated Industries Pages: 64

Brand: G-Tek Pages: 83

GroundCast DRS611

Brand: Vaisala Pages: 12

Solicap M FTI55

Brand: Endress+Hauser Pages: 92

Brand: SOMFY Pages: 40

Brand: Teledyne Lecroy Pages: 4

Cobra SMARTsense Ammonium Ion 12913-00

Brand: PHYWE Pages: 5

Brand: Eno Scientific Pages: 47

Brand: MFJ Pages: 8

Brand: geo-FENNEL Pages: 32

Brand: Readiness Systems Pages: 16

Brand: SED Pages: 52

Brand: STEINEL Pages: 188

ALADIN SPORT PLUS

Brand: ALADIN Pages: 66

Brand: Midtronics Pages: 36

Brand: Myron L Pages: 6

Brand: nux Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands