background image

Wuhan Raycus Fiber Laser Technologies CO., Ltd.

 

                                                                                                                                                                                              P20QB/P30QB

 Pulsed Fiber Laser User’s Guide V2.1

 

 

 

 

stronger,  otherwise  shut  down  the  device  and  check.  If  operating  normally,  the 

marking system can be used in common order afterwards. 

4.3

 

Cautions 

a)

 

Marking  frequency  must  be  in  the  range  of  20  kHz

60  kHz  (P20QB),  or  30  kHz

60kHz    (P30QB). 

b)

 

It should not modulate the frequency while marking. 

c)

 

Stop  marking  first  before  shutting  down  the  device,  then  turn  the  power  down  to  zero 

and cut the power off. 

5.

 

Instructions for warranty, return and maintenance 

5.1

 

General warranty 

All  products  are  warranted  by  Raycus  against  defects  and  problems  in  materials  and 

workmanship  during  the  warranty  period  according  to  the  purchase  order  or  specifications  and 

we guarantee the product will accord with the specification under normal use. 

Raycus  has  the  right  to  choose  to  repair  or  replace  any  product  that  proves  to  be  defective  in 

materials and workmanship selectively during the warranty period. Only products with particular 

defects  are  under  warranty.  Raycus  reserves  the  right  to  issue  a  credit  note  for  any  defective 

products produced in normal conditions. 

5.2

 

Limitations of warranty 

The warranty does not cover the maintenance or reimbursement of our product of which the 

problem  results  from  tampering,  disassembling,  misuse,  accident,  modification,  unsuitable 

physical or operating environment, improper maintenance, damages due to excessive use or not 

following  the  instructions  caused  by  those  who  are  not  from  Raycus.  Customer  has  the 

responsibility to understand and follow this instruction to use the device. Any damage caused by 

fault operating is not warranted. Accessories and fiber connectors are excluded in this warranty. 

According to the warranty, client should write to us within 31 days since the defect is discovered. 

This warranty does not involve any other party, including specified buyer, end-user or customer 

and any parts, equipment or other products produced by other companies. 

5.3

 

Service and repairs 

Raycus is responsible for all the maintenance, for there is no accessory available inside for 

users  to  use.  Please  contact  Raycus  as  soon  as  possible  when  problems  under  warranty  about 

maintenance happen to the product. The product returned with permission should be placed in a 

Summary of Contents for RFL-30QB














Reviews: