Raven Sidekick Pro ISO Installation & Operation Manual Download Page 36

Page: 36 / 82

HAPTER

Sidekick Pro™ ISO Installation & Operation Manual

4. Select the button in the lower, right corner of the product control screen labeled ‘Pump Number: No Cal’ and

select the information icon along the top of the display to access the Product Information screen.

5. Locate the “Node Serial Number” on the Product Information screen and then locate the pump on the vehicle

or implement with the same number on the pump head or side of the injection pump motor.

6. Select the “Set Pump Number” field on the Product Information screen and select the control channel number

to which the pump and chemical tank are assigned. The Product Information screen will display the assigned

value and the UT menu icon will display the assigned pump number in the menu.

7. Repeat this process for each Sidekick Pro ISO Injection Pump connected to the system.

VIRTUAL TERMINAL CALIBRATION

Once installation of the injection system has been verified, and the motor control node is recognized by the

ISOBUS UT control console, the Sidekick Pro™ ISO and UT display must be calibrated to provide accurate control

of the injected product.

Summary of Contents for Sidekick Pro ISO


















































































Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands

Raven Sidekick Pro ISO, Installation & Operation Manual

Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands