manualshive.com logo in svg

Raven AutoBoom XRT, Calibration & Operation Manual

Share
Download
Raven AutoBoom XRT Calibration & Operation Manual Download Page 41

P/N 016-0235-001 Rev. B

37

SETTINGS

FIGURE 24.  Vertical Center Sensor Calibration - Operation Zone

NOTE:

For RoGator, this is low enough that the center rack is able to rotate freely without hitting the travel 

stops. This is typically about 4 in. [10 cm].

8. Touch the Next button to continue the fold calibration.
9. Lower the center rack to a typical operating position and unfold the booms.
10. Touch the Next button to complete the fold calibration.

FIGURE 25.  Vertical Center Sensor Calibration - Set to Spray Position

AUTO CALIBRATION

AutoBoom XRT has a library of calibrated values that are automatically used when the system is initially 

configured. These values have been found to be good defaults specific to your Make, Model, and Boom Width. 

For optimal performance, some of these values should be customized to your specific machine. This helps 

account for differences in hydraulic system performance, oil viscosity, and other characteristics that vary between 

machines. This can be performed automatically using the Auto Calibration feature.

Summary of Contents for AutoBoom XRT









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands