Rauch QUANTRON-A AXIS-M 20 EMC Instruction Manual Download Page 98

Page: 98 / 116

Spreading operation with the QUANTRON-A control unit

5.4

Spreading in the AUTO km/h operating mode

In AUTO km/h operating mode, the control unit automatically controls the actua-
tor depending on the speed signal.

Configure the fertiliser settings:



Application rate (kg/ha)



Working width (m)

Insert fertiliser.

Carry out a calibration to determine the flow factor
or
Obtain the flow factor from the fertiliser chart.

Enter the flow factor manually.

Press the

Start/Stop

key.



The spreading starts.

NOTICE

In order to achieve an optimum spreading result in the AUTO km/h operating
mode, a calibration is to be carried out before starting the spreading work.

Summary of Contents for QUANTRON-A AXIS-M 20 EMC





















































































































Search results

Summary of Contents for QUANTRON-A AXIS-M 20 EMC

Reviews:

Related manuals for QUANTRON-A AXIS-M 20 EMC

Brands by name

Popular brands

Rauch QUANTRON-A AXIS-M 20 EMC, Instruction Manual

Search results

Summary of Contents for QUANTRON-A AXIS-M 20 EMC

Reviews:

Related manuals for QUANTRON-A AXIS-M 20 EMC

Brands by name

Popular brands