background image

12

Installation of the unit into the Housing 

Installations of the unit into the wall 

1. Slide the unit into the housing until it is firmly against the
    rear of the housing. Care is required to ensure the foam
    sealing strips on the housing remain in position. 
2. Connect the air conditioner to the power and position
    excess cord length beneath the air conditioner base.
3. Engage the chassis fixing brackets into the bottom housing
    rail and secure to the base with the screw provided.
4. Remove the front panel from it's carton and plastic bag
    and fit as per the Installation lnstruction.
5. Switch unit on. Check for operation of the unit and check
    for vibration in the installation.
6. Fit the drain pan to the housing and run a drain line to a 
    suitable location if required.

Alternative method of installation if external 
support cannot be provided.

FLASH OR SEAL AROUND EXTERNAL 
WALL FRAME OR ARCHITRAVE

STURDY TIMBER
FRAME

TIMBER FRAMED 
WALL OR PARTITION

SOLID TIMBER SUPPORT

STEADYING BRACKET
(ONE PER SIDE)

DRAIN PAN

ENSURE LOUVRES
ARE ENTIRELY 
OUTSIDE THE WALL

AIR IN

AIR IN

AIR OUT

100mm minimum

OPTION A

AIR IN

LOUVRE

BRICK
WALL

O

45  BRICK CUT AWAY 
TO CLEAR LOUVRES

FRONT

AIR OUT

AIR IN

AIR IN

TOP

VIEW

O

45  BRICK CUT AWAY 
TO CLEAR LOUVRES

100mm

BRICK
WALL

100mm

OPTION B

Step 1

Remove the air conditioner from it's packaging, remove fixing
screws and slide the air conditioner out of it's housing (Refer
to Installation Steps).

Step 2

Prepare the hole in the wall so that the bottom of the housing 
is well supported, the top has minimum clearance and the air 
inlet louvers have clearance as shown below in options  A and
B. Holes from the outside through to the cavity should be 
sealed. The housing should slope down towards the rear by 
about 5mm to allow water formed during operation to drain.

Step 3

Install the housing into the wall and secure. Ensure the foam
seals are not damaged. Flash, seal or fill gaps around the 
inside and outside to provide satisfactory appearance and 
protection against the weather, insects and rodents.
 

Installation of the Housing 

NOTE: UNIT MAY BE SUPPORTED BY A 
            SOLID FRAME FROM BELOW OR 
            BY A HANGER FROM A SOLID
            OVERHEAD SUPPORT.

Preferred method of installation into a timber 
framed wall, partition or window.

FLASH OR SEAL AROUND EXTERNAL 
WALL FRAME OR ARCHITRAVE

STURDY TIMBER
FRAME ALL ROUND 
UNIT

TIMBER FRAMED 
WALL OR PARTITION

EXTERNAL SUPPORT 
FRAME AT BALANCE
POINT OF A/C

ALTERNATIVELY, BRACKETS 
AS ILLUSTRATED BELOW
MAY BE USED.

DRAIN PAN

Summary of Contents for RC-X7T

































Reviews: