RASLOK HCM-T1 Operating Instructions Manual Download Page 4

 

Page 

4

 of 

18

 

 

 

 

 

 
 
 

 

 
 

 

 

 

Important guide during installation / Use

 

To reduce the risks associated with fire and explosion:

 

 

Do not place the equipment in area with potential gas leak, or near heating devices.

 

 

Do not put candles, lit cigarettes, or any heating devices on the unit.

 

 

To reduce the risks associated with hazardous voltage, fire and/or property damage:

 

 

Do not put water containers, chemicals (volatile materials, organic solvents etc.), small metal objects etc.  on top of 
unit to avoid accidental spillage into the unit to cause electric shock or fire.

 

 

To reduce the risks associated with fire and/or property damage:

 

 

Do not place the equipment in an enclosed space where ventilation is difficult, causing overheating at the 

electrical parts.

 

 

To reduce the risks associated with contaminated water and/or property damage:

 

 

Do not clean the equipment with chemicals that could contaminate the water.

 

 

 

NOTICE

 

 

Do  not  install  in  direct  sunlight  or  outdoors  exposed  to  rain  /snow.  The  equipment  is  designed  for indoor 
use only. Large amount of moisture or dust in the equipment surroundings may damage the equipment.

 

 

Do  not  tilt  the  equipment  over  45°  when  transporting  the  unit.  Install  and  keep  the  equipment  on  a flat 
stable  surface.  Unstable  surface  and  inclination  will  cause  performance  degradation  or  equipment 
malfunction.

 

 

Do not connect to hot water source over 40 °C.

 

 

 

Keep  equipment  approximately  10  cm  away  from  the  wall  and  ensure  proper  ventilation  behind  the 
equipment.

 

 

 

Ensure tubing are securely connected and is not bent or pressed down by any heavy objects.

 

 

 

The  disposable  filter  cartridge 

must 

be  replaced  every  12  months,  or  if  any  noticeable  reduction  in  flow 

rate occurs (whichever sooner), to ensure filter effectiveness.

 

 

 

Ensure  the  product  is  connected  to  water  mains  by  a  detachable  tubing  hose.  When  you  relocate  and 
reinstall the appliance, please use a new tubing hose.

 

 

 

This appliance is intended to be used indoors.

 

 

 

Close supervision is required when any appliance is used by or near children.

 

 
 

 

 

Safety Information 

Summary of Contents for HCM-T1



















Reviews: