background image

Fire Hazard

Improper or inadequate 

operation and maintenance 

procedures will cause a fire 

hazard.

Protection  against  inadvertent 

arcing that is capable of 

causing fire or explosion is lost 

if any safety interlocks  are  

disabled  during operation. 

Frequent Power Supply or 

Controller shutdown indicates 

a problem in the system 

requiring correction.

Fire extinguishing equipment must be present in 

the spray area and tested periodically.

Spray areas must be kept clean to prevent the 

accumulation of combustible residues. 

Smoking must never be allowed in the spray area.

The high voltage supplied to the atomizer must be 

turned off prior to cleaning, flushing or maintenance.

When using solvents for cleaning:

 

Those used for equipment flushing should 

have flash points equal to or higher than those 

of the coating material.

 

The flash point of the cleaning solvent shall 

be at least 15° C (27° F) above the ambient 

temperature. Otherwise, the cleaning process 

must be carried out in an area with forced air 

ventilation. It is the end users responsibility to 

insure this condition is met. 

Spray booth ventilation must be kept at the 

rates required by NFPA-33, OSHA, country, and 

local codes.  In addition, ventilation must  be  

maintained  during cleaning operations using 

flammable or combustible solvents.

Electrostatic arcing must be prevented.  Safe 

sparking distance must be maintained between 

the parts being coated and the applicator.  A 

distance of 1 inch for every 10KV of output 

voltage is required at all times.

Test only in areas free of combustible material.

Testing may require high voltage to be on, but 

only as instructed.

Non-factory  replacement  parts  or  

unauthorized equipment modifications may 

cause fire or injury.

If used, the key switch bypass is intended for use 

only during setup operations. Production should 

never be done with safety interlocks disabled.

Never use equipment intended for use in 

waterborne installations to spray solvent based 

materials.

The paint process and equipment should be 

set up and operated in accordance with NFPA-

33, NEC, OSHA, local, country, and European 

Health and Safety Norms.

AREA

Tells where hazards 

may occur.

HAZARD

Tells what the hazard is.

SAFEGUARDS

Tells how to avoid the hazard.

Spray Area

Return To Contents

AH-15-01.2

2

Ranflex Applicators

 - 

SAFETY

Summary of Contents for RansFlex RX 80345


































































Reviews: