background image

33 | 

P a g e

 

 

Warranty Information 

 

1. 

Manufacturer warrants this Product to be free from defects in workmanship and materials for a 

period of Ninety (90) days from the date of purchase, PROVIDED claims are submitted, in writing, 

with proof of purchase.   

2. 

If any part of this item fails because of a manufacturing defect within the Limited Warranty Period, 

Manufacturer  offers to  replace  such  part(s)  provided  that  such  parts  have  not  been  improperly 

repaired, altered, or tampered with or subject to misuse, abuse or exposed to corrosive conditions. 

This  Limited  Warranty  is,  however,  subject  to  certain  limitations,  exclusions,  time  limits  and 

exceptions (Hereinafter “Conditions”) as listed below. Read these Conditions carefully. 

3. 

This  Limited  Warranty  shall  be  limited  to  the  replacement  or  repair  of  any  part(s)  which 

Manufacturer  determines,  after  reasonable  examination,  to  have  been  defective  at  the  time  of 

manufacturing and manufacturer’s obligation(s) shall be limited to replacement, if any, of defective 

part(s) which shall be shipped at Original Purchaser’s expense to Original Purchaser’s designated 

shipping address. 

4. 

This  Limited  Warranty  is  given  to  and  covers  the 

ORIGINAL  PURCHASER  ONLY 

and  such 

coverage terminates Ninety (90) days from the date of purchase.

 

5. 

DAMAGE LIMITATION WARNING: 

IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR 

ANY  INCIDENTIAL  OR  CONSEQUENTIAL  DAMAGES,  INCLUDING  (BUT  NOT  LIMITED TO) 

LOSS  OF  USE  OF  THE  PRODUCT,  LOSS  OF  TIME,  LOSS  OF  FOOD,  INCONVENIENCE, 

EXPENSES FOR TRAVEL, TRANSPORTATION LODGING EXPENSES, LOSS BY DAMAGE TO 

PERSONAL PROPERTY OR LOSS OF INCOME, PROFITS OR REVENUE. 

6. 

MANUFACTURER’S OBLIGATION:

 Manufacturer’s liability shall be  limited to the delivery of a 

good, merchantable Product and, if necessary, the repair or replacement, at manufacturer’s option, 

of any defective part or unit. 

7. 

TRANSFER LIMITATIONS:

 This Limited Warranty is not assignable or transferable.  It covers only 

the original purchaser. 

8. 

RESERVED  RIGHT  TO  CHANGE:

  Manufacturer  reserves  the  right  to  make  changes  or 

improvements to products it produces in the future without imposing on itself any obligations to 

install the same improvements in the products it has previously manufactured. 

9. 

This Limited Warranty gives the Original Purchaser specific legal rights but there may be other 

rights which vary by jurisdiction. 

10. This warranty does not cover the following items: 

  Chips or scratches on porcelain or painted surfaces. 

  Rust or corrosion is not deemed a manufacturing or materials defect. 

  Discoloration or loss of paint due to handling during assembly, heat or cleaning products. Paint 

may require touch up. 

  Stainless steel discoloration or corrosion. 

  Consumables such as batteries. 

 

IF CUSTOMER SERVICE BECOME NECESSARY:

 

1. 

The Original Purchaser is responsible for shipping and handling charges of the returned item(s) 

and replacement parts, if any. 

2. 

All parts to be replaced will need to be shipped before replacement items will be sent. 

3. 

Follow the Customer Service Representative’s instructions exactly. If a return  is necessary, it 

must be packed carefully and shipped prepaid. 

 

Should you encounter any problem, 

CALL US FIRST. 

Do not return product to the store. 

WE CAN HELP. 

 

For assistance, contact customer service at 

[email protected]

 

or at 1-888-837-1380, Mon to Fri, 8:00am – 5:00pm Pacific Standard time

 

 

Manufacturer information 

Rankam (China) Manufacturing Company Limited 

Address: 18/F, New Lee Wah Centre, 88 Tokwawan Road, Kowloon, Hong Kong.

 

Summary of Contents for 980014462



































Reviews: