background image

Charging :

A. Manual Charging

01. You can directly charge the cleaner with its power adapter or with the charging dock station.
02. When charging directly via the power adaptor, please connect the output plug of the adapter with the
      charging socket on the robot. (See figure 1)
03. When charging with the charging dock station, please first connect the adapter to it, and then place
       the cleaner tightly against the dock station to ensure a nicer contact between the charging electrode
      of the cleaner and the charging terminal on the dock station. (See figure 2)
04. During the charging process, the display will show the charging status, and the battery level bars will
      turn red from the 1

st

 bar to the 3

rd

 bar in order repeatedly. (See figure 3)

05. Upon completion of the charging, the display will show 3 fully red bars. (See figure 4)

High tension! Avoid electric shock.
Please operate with a dry hand!

High tension! Avoid electric shock.
Please operate with a dry hand!

 Figure 1

 Figure 2

 Figure 3

 Figure 4

1. Take out the battery before disposing of the robot.

2. Always remember to cut off the power before removing

    the battery.

3. Recycle or dispose of the battery properly.

4. To avoid explosion, never throw it into fire!

B. Self-Charging

01. The cleaner will automatically start to search the charging dock station for recharge when the battery
      level is lower than 15% during cleaning process.
02. When press the 

DOCKING

 button on the cover of the robot or the remote controller, the function of

      self-charging will also be enabled.
03. During the above “DOCKING” mode, press any other button on cleaner or remote controller, the
      cleaner will stop searching and enter the standby status. The directional buttons on the remote
      controller can also be used to support the searching function.

Summary of Contents for M-788

















Reviews: