Manual-
MLM 82a
MIC/LINE MIXER
OPERATORS MANUAL
MLM 82a CONNECTION
When connecting the MLM 82a to other components in
your system for the first time, leave the power supply for last.
This gives you a chance to make mistakes and correct them with-
out damage to your fragile speakers, ears and nerves.
MIC/LINE INPUTS 1-4
The four XLR jacks provided on the MLM 82a are balanced
MIC/LINE inputs. They will also accept unbalanced connec-
tors. Use only shielded cable for inputs. For best noise rejection
use two-conductor-plus-shielded wire, even for unbalanced
operation. Connect the shield at both ends to help insure proper
grounding. See the Sound System Interconnection RaneNote
included with this manual for all cable adaptations. Rane follows
the AES recommended practice of pin 2 positive, pin 3 negative,
and pin 1 to shield. Switch any input connected to a microphone
to the MIC position (
out
) using the associated switches on the
rear panel. When connecting line level signals, switch the input
to the LINE position (in). A single phantom power switch is
provided for the four MIC inputs.
If LINE is selected, Phantom
Power is disabled for that input.
QUICK START
This section is provided as a convenience for those in a rush. If you are experienced with this unit or other Rane products, these
few words will refresh your memory.
INPUTS 1
through
4
may be microphone or line level. The choice between the two is made by setting the
LINE
push buttons
on the REAR of the unit next to the
MIC/LINE INPUT JACKS
. Each microphone input may be assigned to
A
,
B
or
A+B
outputs
using the front panel
ASSIGN
switches.
INPUTS 5
through
8
are stereo line inputs which may be set to mono using the recessed
MONO
switches located on the front
panel.
Internal switches allow setting output signal levels for
MIC
or
LINE.
The factory default setting is
LINE
. If the MLM 82a is
connected directly to a power amplifier, equalizer or recorder input, choose
LINE
level. If the MLM 82a is connected to a micro-
phone jack of an existing sound system, choose
MIC
level.
Once Inputs, Outputs, and power are properly connected, with the
OUTPUT LEVELS
counterclockwise (
off
), set the Input
LEVELS
as high as possible without causing the
SIG/OL
indicators to blink red except during extreme signal peaks. Now slowly
raise the
OUTPUT LEVELS
as desired.
Never connect anything except an approved Rane power supply to the red thing that looks like a telephone jack on the rear
of the MLM 82a.
This is an AC input and requires special attention if you do not have a power supply
exactly
like the one that was
originally packed with your unit. See the full explanation of the power supply requirements on page Manual-3.
STEREO LINE INPUTS 5-8
The ¼" connectors are line-level balanced/unbalanced
Inputs. If the MLM 82a is to be used with unbalanced sources,
consult the Sound System Interconnection RaneNote included
with this manual for proper wiring. Stereo Inputs use both A
and B jacks at each INPUT. INPUTS 5 through 8 also serve as
mono Inputs when the front panel MONO switch is engaged.
OUTPUTS
The MLM 82a’s OUTPUTS are balanced. The same wiring
conventions as the XLR Inputs apply. The type of device follow-
ing the MLM 82a must be considered when setting the internal
Output Level switch. Choose between LINE (0 dB) or MIC
(-40 dB) output, the factory setting is LINE. If the MLM 82a
is connected directly to a power amplifier input, choose LINE
level. If the MLM
82a is connected to a
microphone jack on an
existing sound system,
choose MIC level. For
unbalanced OUTPUT
connections
do not
tie pin 3 (i.e. “–”) to
ground.
WEAR PARTS:
This product contains no wear parts.
MIC/LINE MIXER
10
0
2
4
8
6
10
0
2
4
8
6
10
0
2
4
8
6
10
0
2
4
8
6
10
0
2
4
8
6
10
0
2
4
8
6
10
0
2
4
8
6
10
0
2
4
8
6
10
0
2
4
8
6
10
0
2
4
8
6
MLM 82a
POWER
OUTPUTS
1
MONO MIC/LINE INPUTS
2
3
4
7
5
6
STEREO LINE INPUTS
8
LEVEL
LEVEL
LEVEL
LEVEL
OL
OL
OL
LEVEL
A+B
ASSIGN
A
B
A+B
ASSIGN
A
B
A+B
ASSIGN
A
B
A+B
ASSIGN
A
B
LEVEL
LEVEL
MONO
MONO
SIG
OL
SIG
OL
SIG
OL
SIG
MONO
MONO
LEVEL
LEVEL
LEVEL
B
A
OUTPUTS
A
AC IN
B
