manualshive.com logo in svg

R&S CMW-KG4 Series, User Manual, Page: 450 / 988

Share
Download
R&S CMW-KG4 Series User Manual Download Page 450

WCDMA Signaling

R&S

®

CMW-KG4xx/-KM4xx/-KS4xx

450

User Manual 1173.9657.02 ─ 11

CONFigure:WCDMa:SIGN<i>:CELL:HSUPa:MCCode 

<Code>

Specifies the "Maximum channelisation codes" value signaled to the UE. Depending
on several other HSUPA parameters, e.g. the UE category, only a subset of values is
allowed.

Parameters:

<Code>

S64 | S32 | S16 | S8 | S4 | S24 | S22 | S224

S64, S32, S16, S8, S4

: one code, SF 64 to SF 4

S24

: two codes, SF 4

S22

: two codes, SF 2

S224

: four codes, two with SF 2 and two with SF 4

*RST: 

S224

Example: 

See 

Configuring HSUPA Settings

Firmware/Software: 

V3.0.20

Options: 

R&S CMW-KS401

Manual operation:

See 

"Maximum Channelisation Code"

 

on page 214

CONFigure:WCDMa:SIGN<i>:CELL:HSUPa:ISGRant 

<Grant>[, <Type>]

Specifies initial serving grant parameters signaled to the UE. If you only want to modify
the <Grant> you may omit the <Type> parameter.

Parameters:

<Grant>

"Serving Grant value" information element
Range: 

0  to  38

*RST: 

13 (OFF)

Additional parameters: OFF | ON (disable | enable transmission
of the initial serving grant parameters)

<Type>

PRIMary | SECondary
"Primary/Secondary Grant Selector" information element
*RST: 

PRIM

Example: 

See 

Configuring HSUPA Settings

Firmware/Software: 

V3.0.20

Options: 

R&S CMW-KS401

Manual operation:

See 

"Initial Serving Grant"

 

on page 214

CONFigure:WCDMa:SIGN<i>:CELL:HSUPa:MODulation 

<Modulation>

Selects the E-DCH modulation scheme to be used during HSUPA connection.

Command Reference

深圳德标仪器 

135-1095-0799

Summary of Contents for CMW-KG4 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments