background image

 

Unifiedbrands.net         

7

 

 
 

5.  Inbound  costs  on  factory  supplied  items  to  be  responsibility  of  the 

customer. 

6.  Extended  warranty  options  are  not  available  for  parts,  labor,  or 

compressors from the factory. 

 
ITEMS NOT COVERED UNDER WARRANTY 

1.  Maintenance type of repairs such as condenser cleaning, temperature 

adjustments, clogged drains, unit leveling and re-application of silicone. 

2.  Unified Brands does not cover gaskets under warranty.  Gaskets are a 

maintenance  type  component  that  are  subject  to  daily  wear  and  tear 
and  are the  responsibility  of the  owner  of the  equipment.    Because  of 
the unlimited number of customer related circumstances that can cause 
gasket  failure  all  gasket  replacement  issues  are  considered  non-
warranty.    Unified  Brands  recommends  thorough  cleaning  of  gaskets 
on a weekly basis with a mild dish soap and warm water.  With proper 
care Unified Brands gaskets can last up to two years, at which time we 
recommend  replacement  of  all  gaskets  on  the  equipment  for  the  best 
possible performance. 

 

NOTICE:  FOOD LOSS IS NOT COVERED UNDER WARRANTY  

 

3.  Repairs  caused  by  abuse  such  as  broken  glass,  freight  damage,  or 

scratches and dents. 

4.  Electrical  component  failure  due  to  water  damage  from  cleaning 

procedures. 

 
QUOTATIONS 
Verbal  quotations  are  provided  for  customer  convenience  only  and  are 
considered  invalid  in  the  absence  of  a  written  quotation.    Written  quotations 
from  Unified  Brands  are  valid  for  30  days  from  quote  date  unless  otherwise 
specified.    Unified  Brands  assumes  no  liability  for  dealer  quotations  to  end-
users. 
 
SPECIFICATION & PRODUCT DESIGN 
Due to continued product improvement, specification and product design may 
change  without  notice.    Such  revisions  do  not  entitle  the  buyer  to  additions.  
Changes or replacements for previously purchased equipment. 

 

SANITATION REQUIREMENTS 
Certain  areas  require  specific  annotation  requirements  other  than  N.S.F.  & 
U.L. standards.  Unified Brands must be advised of these specifications before 
fabrication of equipment.  In these special circumstances, a revised quotation 
may  be  required  to  cover  additional  costs.    Failure  to  notify  Unified  Brands 
before fabrication holds the dealer accountable for all additional charges. 
 

 

 

Warranty Policies (cont.) 

Summary of Contents for 9215-32-7




























Reviews: