background image

OM 914244-0414-G

RAMSEY WINCH warrants each new RAMSEY WINCH to be free from defects in material and workmanship for a period of one (1) 

year from date of purchase.

The obliga on under this warranty, statutory or otherwise, is limited to the replacement or repair at the Manufacturer’s factory, or 

at a point designated by the Manufacturer, of such part that shall appear to the Manufacturer, upon inspec on of such part, to have 

been defec ve in material or workmanship. 

This warranty does not obligate RAMSEY WINCH to bear the cost of labor or transporta on charges in connec on with the replace-

ment or repair of defec ve parts, nor shall it apply to a product upon which repair or altera ons have been made, unless authorized 

by Manufacturer, or for equipment misused, neglected or which has not been installed correctly.

RAMSEY WINCH shall in no event be liable for special or consequen al damages. RAMSEY WINCH makes no warranty in respect to 

accessories such as being subject to the warran es of their respec ve manufacturers.

RAMSEY  WINCH,  whose  policy  is  one  of  con nuous  improvement,  reserves  the  right  to  improve  its  products  through  changes  in 

design or materials as it may deem desirable without being obligated to incorporate such changes in products of prior manufacture.

If fi eld service at the request of the Buyer is rendered and the fault is found not to be with RAMSEY WINCH’s product, the Buyer shall 

pay the  me and expense to the fi eld representa ve. Bills for service, labor or other expenses that have been incurred by the Buyer 

without approval or authoriza on by RAMSEY WINCH will not be accepted.

See warranty card for details.

RAMSEY WINCH COMPANY

Post Offi ce Box 581510 Tulsa, Oklahoma 74158-1510

 

Telephone: (918) 438-2760 FAX: (918) 438-6688 

LIMITED WARRANTY

Summary of Contents for HD-P50000





















Reviews: