background image

SBRGB 

 1  

Ramsey Electronics Model No.           SBRGB 

Get your surface mount practice on this nifty little kit! When 
assembled, the RGB full color LED will cycle through an array of 
mesmerizing colors! Makes for an excellent attention getter or 
name badge light like no other! 

Bright full-color LED (not a single white element) with independently 
drivable red, green and blue LED elements. These elements are 
matched for a true “white” output or any color in between! 

Uses PWM methods to select any color with a simple 8-pin micro-
controller. Switch-able speed selection and transition mode as well! 

Get your feet wet with surface mount technology on this fun little 
project, not one that’s too complicated or too expensive. Build 
several and give them to your friends! 

Very small PC board for easy placement of this attention getter 
almost anywhere! 

Operates from 6V to 12VDC, includes a 9V battery snap! 

Kit even includes a few extra SMT parts in case you loose some! 

Clear, concise instructions to guide you step-by-step to a finished 
product that works the FIRST time! 

SUPER BLINKY 
SMT PRACTICE KIT 

Summary of Contents for SBRGB





















Reviews: