background image

AM25 

1  

 

Ramsey Electronics Model No.              AM25 

Ever want to be your own disc jockey or talk show host ? Build  
and run your own AM broadcast station with this exciting kit ! 
The AM25 transmitter offers a professional quality signal that is 
free from frequency drift and programmable to anywhere in the 
AM broadcast band !  

Great for transmitting your tape deck, CD player, or voice 
throughout the house, yard, or car ! 

Powerful enough for high school, college, or neighborhood radio 
station - in use the world over ! 

Easily programmed via DIP switch to any clear channel on the AM 
broadcast band - from 540 to 1710 KHz. 

Operates on the same principle as the “big-boys”, learn how 
commercial transmitters work as well ! 

Superior performance - transmits up to 1/4 mile ! 

Adjustable transmit power level, low pass filtered output. 

Unit runs on 9 - 15 volts DC. 

Handy information on FCC rules and antenna hints. 

Complete and informative instructions guide you to a kit that works 
the first time, every time - enhances resale value, too ! 

 

SYNTHESIZED AM 

BROADCAST 

TRANSMITTER KIT

 

Summary of Contents for AM25

























Reviews: