background image

 

 

 

II CONTROL
 

It is necessary to become familiar with the location and purpose of each control before 
operating the Mini-Skid. 
 

ENGINE CONTROLS – KAWASAKI 27 HP GASOLINE 

 

Low Fuel Indicator   

 

 

 

 

 

 

Low Hyd. 

 

 

 

 

 

 

 

 

 

 

 

Oil Indicator 

Low Oil Warning  
Light   

 

 

 

 

 

 

 

 

Tachometer/ 

 

 

 

 

Hour Meter 

Throttle Control 
 

 

 

 

 

 

 

 

 

 

Ignition  

Engine Temperature  

 

 

 

 

 

 

Switch 

Indicator 
 

 

 

 

 

 

 

 

 

 

Light Switch 

Choke Control 

Figure 1:  Kawasaki Instrument Panel 

 
 

Choke Control

 – Pull choke control out 

to start a cold engine.  As the engine 
warms up push choke control in 
gradually 
 

Throttle Control

 – When the Throttle 

control lever is set down the engine is at 
idle speed.  Pushing the control up 
increased the engine speed 
 

Low Oil Warning Light

 – This light 

illuminates if the engine oil is low.  Stop 
the engine and add oil immediately if the 
light comes on 
 

Ignition Switch

 – The ignition switch is 

a three-position switch.  Clockwise from 
the OFF position are the ON and start 
position. 
 

Engine Temperature Light

 – This light 

illuminates if the engine temperature 
becomes too hot.  Shut off the engine 
immediately 
 
 
 

IMPORTANT 

Be Sure Ignition Key Is In Off Position, 

Or Even Removed, When The Engine Is 

Not Running 

 
 
 
 
 

IMPORTANT 

For Maximum Power While Working, 

The Engine Should Be Running At Full 

Throttle 

 

 

Summary of Contents for 950


































Reviews: