manualshive.com logo in svg

RAM 1500 2023, Owner'S Manual, Page: 96 / 416

Share
Download
RAM 1500 2023 Owner'S Manual Download Page 96

94

GETTING TO KNOW YOUR INSTRUMENT PANEL

 

M

IDLINE

 I

NSTRUMENT

 C

LUSTER

 

D

ESCRIPTIONS

 — G

ASOLINE

1. Tachometer

Indicates the engine speed in revolutions per 

minute (RPM x 1000).

2. Voltmeter

When the vehicle is in the RUN state, the gauge 

indicates the electrical system voltage. The 

pointer should stay within the normal range if the 

battery is charged. If the pointer moves to either 

extreme left or right and remains there during 

normal driving, the electrical system should be 

serviced.

NOTE:

In vehicles equipped with Stop/Start, a reduced voltage 

may be present during an Autostop.
3. Instrument Cluster Display

When the appropriate conditions exist, this display 

shows the instrument cluster display messages  

Ú

page 98.

The display always shows one of the main menu 

items after ignition on.

4. Oil Pressure Gauge

The pointer should always indicate the oil pres

-

sure when the engine is running. A continuous 

high or low reading under normal driving condi

-

tions may indicate a lubrication system malfunc

-

tion. Immediate service should be obtained from 

an authorized dealer.

NOTE:

In vehicles equipped with Stop/Start, an oil pressure indi

-

cation of zero is normal during an Autostop.
5. Speedometer

Indicates vehicle speed.

6. Temperature Gauge

The pointer shows engine coolant temperature. 

The pointer positioned within the normal range 

indicates that the engine cooling system is oper

-

ating satisfactorily.

The pointer will likely indicate a higher tempera

-

ture when driving in hot weather, up mountain 

grades, or when towing a trailer. It should not be 

allowed to exceed the upper limits of the normal 

operating range.

7. Fuel Gauge

The pointer shows the level of fuel in the fuel tank 

when the ignition is in the ON/RUN position.

 The fuel pump symbol points to the 

side of the vehicle where the fuel door 

is located.

WARNING!

A hot engine cooling system is dangerous. You or others 

could be badly burned by steam or boiling coolant. 

You may want to call an authorized dealer for service if 

your vehicle overheats  

Ú

page 350.

CAUTION!

Driving with a hot engine cooling system could damage 

your vehicle. If the temperature gauge reads “H,” pull 

over and stop the vehicle. Idle the vehicle with the air 

conditioner turned off until the pointer drops back into 

the normal range. If the pointer remains on the “H,” 

turn the engine off immediately and call an authorized 

dealer for service.

23_DT_OM_EN_USC_t.book  Page 94  

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Reviews:

No comments