RAM 1500 2023 Owner'S Manual Download Page 34

Page: 34 / 416

GETTING TO KNOW YOUR VEHICLE

Reclining Rear Seats — If Equipped

The recliner handle is located on the front of the rear

outboard seat cushions. To adjust the seatback, lift

upward on the handle, and slide the seat bottom forward.

The lower portion of the seatback will tilt rearward. When

you reach the desired position, release the handle.

Rear Seat Recliner Handle Locations

NOTE:

This feature is not available if vehicle is equipped with rear

bench seat.

OWER

DJUSTMENT

RONT

EATS

) —

QUIPPED

Some models may be equipped with eight-way power

driver and passenger seats. The power seat switches are

located on the outboard side of the driver and passenger

seat cushions. There are two power seat switches that are

used to control the movement of the seat cushion and the

seatback.

Power Seat Switches

Adjusting The Seat Forward Or Rearward

The seat can be adjusted both forward and rearward by

using the power seat switch. The seat will move in the

direction of the switch. Release the switch when the

desired position has been reached.

Adjusting The Seat Up Or Down

The height of the seats can be adjusted up or down by

using the power seat switch. The seat will move in the

direction of the switch. Release the switch when the

desired position has been reached.

Tilting The Seat Up Or Down

The angle of the seat cushion can be adjusted up or down

using the power seat switch. The front of the seat cushion

will move in the direction of the switch. Release the switch

when the desired position has been reached.

Reclining The Seatback

The angle of the seatback can be adjusted forward or

rearward by using the power seat switch. The seat will

move in the direction of the switch. Release the switch

when the desired position is reached.

WARNING!

Do not ride with the seatback reclined so that the

shoulder belt is no longer resting against your chest. In

a collision you could slide under the seat belt, which

could result in serious injury or death.

1 — Power Seat Switch
2 — Power Seatback Switch

WARNING!



Adjusting a seat while driving may be dangerous.

Moving a seat while driving could result in loss of

control which could cause a collision and serious

injury or death.



Seats should be adjusted before fastening the

seat belts and while the vehicle is parked. Serious

injury or death could result from a poorly adjusted

seat belt.



Do not ride with the seatback reclined so that the

shoulder belt is no longer resting against your chest.

In a collision you could slide under the seat belt,

which could result in serious injury or death.

23_DT_OM_EN_USC_t.book Page 32

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

RAM 1500 2023, Owner'S Manual, Page: 34 / 416

Search results

Summary of Contents for 1500 2023

Reviews: