RAM 1500 2023 Page 274 Owner'S Manual Download

Page: 274 / 416

272

SAFETY

When RCP is on and the vehicle is in REVERSE (R), the

driver is alerted using both the visual and audible alarms,

including reducing the radio volume.

NOTE:

In a parking lot situation, oncoming vehicles can be

blocked by vehicles parked on either side. If the sensors

are blocked by other structures or vehicles, the system will

not be able to alert the driver.

Blind Spot Modes

Blind Spot has three selectable modes of operation that

are available in the Uconnect system.
Blind Spot Alert Lights Only
When operating in Blind Spot Alert mode, the BSM system

will provide a visual alert in the appropriate side view

mirror based on a detected object. However, when the

system is operating in Rear Cross Path (RCP) mode, the

system will respond with both visual and audible alerts

when a detected object is present. Whenever an audible

alert is requested, the radio is muted.

Blind Spot Alert Lights/Chime
When operating in Blind Spot Alert Lights/Chime mode,

the BSM system will provide a visual alert in the

appropriate side view mirror based on a detected object.

If the turn signal is then activated, and it corresponds to

an alert present on that side of the vehicle, an audible

chime will also be sounded. Whenever a turn signal and

detected object are present on the same side at the same

time, both the visual and audible alerts will be issued. In

addition to the audible alert the radio (if on) will also be

muted.

NOTE:

Whenever an audible alert is requested by the BSM

system, the radio is also muted.
When the system is in RCP, the system shall respond with

both visual and audible alerts when a detected object is

present. Whenever an audible alert is requested, the radio

is also muted. Turn/hazard signal status is ignored; the

RCP state always requests the chime.
Blind Spot Alert Off
When the BSM system is turned off there will be no visual

or audible alerts from either the BSM, RCP, or Trailer

Merge Assist systems.

NOTE:

The BSM system will store the current operating mode

when the vehicle is shut off. Each time the vehicle is

started the previously stored mode will be recalled and

used.

Trailer Merge Assist — If Equipped

Trailer Merge Assist is a function of the Blind Spot

Monitoring (BSM) system that extends the blind spot zone

to work while pulling a trailer.

NOTE:

When Trailer Merge Assist is activated, Rear Cross Path is

disabled.
Trailer Merge Assist consists of three sub functions:



Automatic Trailer Detection



Trailer Length Detection



Trailer Merge Warning

Blind Spot Zones With Trailer Merge Assist

WARNING!

Rear Cross Path Detection (RCP) is not a backup aid

system. It is intended to be used to help a driver detect

an oncoming vehicle in a parking lot situation. Drivers

must be careful when backing up, even when using

RCP. Always check carefully behind your vehicle, look

behind you, and be sure to check for pedestrians,

animals, other vehicles, obstructions, and blind spots

before backing up. Failure to do so can result in serious

injury or death.

1 — Vehicle
2 — Trailer

23_DT_OM_EN_USC_t.book Page 272

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands