RAM 1500 2023 Page 160 Owner'S Manual Download

Page: 160 / 416

158

STARTING AND OPERATING

NOTE:



The driver is always responsible for controlling the

vehicle, responsible for any surrounding objects, and

must intervene as required.



The system is provided to assist the driver and not to

substitute the driver.



During a semi-automatic maneuver, if the driver

touches the steering wheel after being instructed to

remove their hands from the steering wheel, the

system will cancel, and the driver will be required to

manually complete the parking maneuver.



The system may not work in all conditions

(e.g. environmental conditions such as heavy rain,

snow, etc., or if searching for a parking space that has

surfaces that will absorb the ultrasonic sensor waves).



New vehicles from the dealership must have at least

30 miles (48 km) accumulated before the ParkSense

Active Park Assist system is fully calibrated and

performs accurately. This is due to the system’s

dynamic vehicle calibration to improve the perfor

mance of the feature.



The driver must control the vehicle’s brakes. The auto

matic emergency braking feature is NOT intended to

substitute for the driver during REVERSE maneuvers.

NABLING

ISABLING

ARK

ENSE

CTIVE

ARK

SSIST

YSTEM

The ParkSense Active Park Assist system can

be enabled and disabled with the ParkSense

Active Park Assist switch, located on the switch

panel below the Uconnect display.

NOTE:

If your vehicle is equipped with a 12-inch Uconnect

display, the ParkSense Active Park Assist switch is located

above the display.
To enable or disable the ParkSense Active Park Assist

system, push the ParkSense Active Park Assist switch

once (LED turns on). Pushing the switch a second time will

disable the system (LED turns off).
The ParkSense Active Park Assist system will turn off

automatically for any of the following conditions:



Parking maneuver is completed.



Vehicle speed is greater than 18 mph (30 km/h) when

searching for a parking space.



Vehicle speed is greater than 5 mph (7 km/h) during

active steering guidance into the parking space.



Steering wheel is touched during active steering guid

ance into the parking space.



ParkSense Front/Rear Park Assist switch is pushed.



Driver's door is opened.



Tailgate is opened.



Electronic Stability Control/Anti-Lock Braking System

intervention.



Vehicle is in 4WD Low.



Axle Locker is active.



Trailer is connected.



Trailer Reverse Steering Control (TRSC) is active.



Snowplow is connected.

NOTE:

The ParkSense Active Park Assist system will allow a

maximum of eight shifts between DRIVE and REVERSE. If

the maneuver cannot be completed within eight shifts, the

system will cancel and the instrument cluster display will

instruct the driver to complete the maneuver manually.
The ParkSense Active Park Assist system will only operate

and search for a parking space when the following

conditions are present:



Gear selector is in DRIVE.



The ignition is in the ON/RUN position.



The ParkSense Active Park Assist switch is activated.



Driver's door is closed.



Tailgate is closed.



Vehicle speed is less than 15 mph (25 km/h).



The outer surface and the underside of the front and

rear fascias/bumpers are clean and clear of snow, ice,

mud, dirt or other obstruction.

NOTE:

If the vehicle is driven above approximately 15 mph

(25 km/h), the instrument cluster display will instruct the

driver to slow down. If the vehicle is driven above approxi

mately 18 mph (30 km/h), the system will cancel. The

driver must then reactivate the system by pushing the

ParkSense Active Park Assist switch.

23_DT_OM_EN_USC_t.book Page 158

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands