RAM 1500 2023 Page 127 Owner'S Manual Download

Page: 127 / 416

STARTING AND OPERATING

125

GNITION

ARK

NTERLOCK

This vehicle is equipped with an Ignition Park Interlock

which requires the transmission to be in PARK before the

ignition can be turned to the OFF position. This helps the

driver avoid inadvertently leaving the vehicle without

placing the transmission in PARK. This system also locks

the transmission in PARK whenever the ignition is in the

OFF position.

NOTE:

The transmission is NOT locked in PARK when the ignition

is in the ACC position (even though the engine will be off).

Ensure that the transmission is in PARK, and the ignition

is OFF (not in ACC position) before exiting the vehicle.

RAKE

RANSMISSION

HIFT

NTERLOCK

(BTSI) S

YSTEM

This vehicle is equipped with a BTSI system that holds the

transmission gear selector in PARK unless the brakes are

applied. To shift the transmission out of PARK, the engine

must be running and the brake pedal must be pressed.

The brake pedal must also be pressed to shift from

NEUTRAL into DRIVE or REVERSE when the vehicle is

stopped or moving at low speeds.

8-S

PEED

UTOMATIC

RANSMISSION

Rotary Shifter — If Equipped
The transmission is controlled using a rotary electronic

gear selector located on the instrument panel. The

transmission gear range (PRND) is displayed both above

the gear selector and in the instrument cluster. To select

a gear range, simply rotate the gear selector. You must

press the brake pedal to shift the transmission out of

PARK (or NEUTRAL, when the vehicle is stopped or moving

at low speeds). To shift past multiple gear ranges at once

(such as PARK to DRIVE), simply rotate the gear selector

to the appropriate detent. Select the DRIVE range for

normal driving.

NOTE:

In the event of a mismatch between the gear selector

position and the actual transmission gear (for example,

driver selects PARK while driving), the position indicator

will blink continuously until the selector is returned to the

proper position, or the requested shift can be completed.
The electronically controlled transmission adapts its shift

schedule based on driver inputs, along with environmental

and road conditions. The transmission electronics are

self-calibrating; therefore, the first few shifts on a new

vehicle may be somewhat abrupt. This is a normal

condition, and precision shifts will develop within a few

hundred miles (kilometers).



Unintended movement of a vehicle could injure

those in or near the vehicle. As with all vehicles, you

should never exit a vehicle while the engine is

running. Before exiting a vehicle, always come to a

complete stop, then apply the parking brake, shift

the transmission into PARK, and turn the ignition

OFF. When the ignition is in the OFF position, the

transmission is locked in PARK, securing the vehicle

against unwanted movement.



When exiting the vehicle, always make sure the

ignition is in the OFF position, remove the key fob

from the vehicle, and lock the vehicle.



Never leave children alone in a vehicle, or with

access to an unlocked vehicle. Allowing children to

be in a vehicle unattended is dangerous for a

number of reasons. A child or others could be seri

ously or fatally injured. Children should be warned

not to touch the parking brake, brake pedal or the

transmission gear selector.



Do not leave the key fob in or near the vehicle

(or in a location accessible to children), and do not

leave the ignition in the ACC or ON/RUN position.

A child could operate power windows, other controls,

or move the vehicle.

WARNING!

CAUTION!



Shift into or out of PARK or REVERSE only after the

vehicle has come to a complete stop.



Do not shift between PARK, REVERSE, NEUTRAL, or

DRIVE when the engine is above idle speed.



Before shifting into any gear, make sure your foot is

firmly pressing the brake pedal.

23_DT_OM_EN_USC_t.book Page 125

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands